801309
15
Zoom out
Zoom in
Previous page
1/22
Next page
Installing the Transducer on a Pole
You can use the included hardware to install the transducer on a pole (not included). Installing the transducer
on a pole is similar to installing the transducer on a trolling motor shaft. If needed, you can refer to the
diagram provided for installing the transducer on a trolling motor shaft when installing the transducer on a pole
(Installing the Transducer on the Trolling Motor Shaft, page11).
NOTE: You can use the included flat bracket for mounting the transducer on a pole.
Labels identifying the parts bags required for this procedure:
NOTICE
You must secure the transducer cable to the pole or other secure location during installation. Damage to the
transducer cable wire or the cable jacket can cause transducer failure.
1Remove the back of the pole-mount bracket and four screws from parts bag .
2Remove the front half of the pole-mount bracket from parts bag .
3If the pole is equal to or less than 25mm (1in.) in diameter, remove the rubber liner from parts bag .
4If the pole is equal to or less than 25mm (1in.) in diameter, wrap the rubber liner around the pole in the
location you want to install the mount.
5Place the pole-mount bracket around the rubber liner on the pole.
6Insert the screws into the pole-mount bracket, and secure them using the M6 hex wrench in parts bag .
7Remove the knob from parts bag .
8Place the transducer against the pole-mount bracket, and secure it using the knob.
NOTE: You can secure the transducer to the mount using the included low-profile hardware instead of the
knob if you do not plan to switch transducer modes frequently during use (Installing the Transducer Using
Low Profile Mounting Hardware, page14).
9Secure the transducer cable to the pole or other secure location, and route the cable to the location of the
sonar module.
Mounting the GLS 10 Black Box Device
NOTICE
If you are mounting the device in fiberglass, when drilling the pilot holes, use a countersink bit to drill a
clearance counterbore through only the top gel-coat layer. This will help to avoid cracking in the gel-coat layer
when the screws are tightened.
NOTE: Screws are included with the device, but they may not be suitable for the mounting surface.
Before you mount the device, you must select a mounting location, and determine what screws and other
mounting hardware are needed for the surface.
1Place the black box device in the mounting location, and mark the location of the pilot holes.
2Drill a pilot hole for one corner of the device.
3Loosely fasten the device to the mounting surface with one corner, and examine the other three pilot-hole
marks.
4Mark new pilot-hole locations if necessary, and remove the device from the mounting surface.
5Drill the remaining pilot holes.
6Secure the device to the mounting location.
15
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin LIVESCOPE XR LVS62 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin LIVESCOPE XR LVS62 in the language / languages: English as an attachment in your email.

The manual is 4.09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin LIVESCOPE XR LVS62

Garmin LIVESCOPE XR LVS62 Installation Guide - German - 22 pages

Garmin LIVESCOPE XR LVS62 Installation Guide - Dutch - 22 pages

Garmin LIVESCOPE XR LVS62 Installation Guide - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info