579859

Garmin GTN 725 Manual

398
Zoom out
Zoom in
Previous page
1/412
Next page
GTN 6XX/7XX AML STC Installation Manual 190-01007-A3
Page G-2 Rev. 4
CAUTION
All overbraid ends must be secured outside the backshell by the strain relief
bar. Failure to do so may allow overbraid ends to contact and short HSDB
pins, resulting in weather radar malfunction or damage.
6. At the bulkhead end of the overbraid (or grounding provisions at the metallic wing entry area),
comb out a maximum of two inches of braid, twist it, cut to length if necessary, and terminate it
in a terminal lug. Refer to Figure G-1.
7. Secure the overbraid pigtail to a terminal stud.
G.1.1.3 Overbraid Terminal Bonding
Electrical bond preparation for all aluminum-to-aluminum interfaces must be done in accordance with
SAE ARP1870 Sections 5.1 and 5.5. The overbraid terminal lug must be electrically bonded to a 5/16”
stud installed in accordance with AC 43.13-1B Section 11-189, as well as the following restrictions:
1. If possible, use an existing tooling hole to install the stud.
2. If no suitable tooling hole exists, use an existing fastener (5/16” or larger).
NOTE
Installation of a stud into a pressure bulkhead is not authorized under this STC. If a new
stud must be installed into a pressure bulkhead, additional approval for installation of the
stud will be required.
3. If there is no suitable fastener, install a new stud as follows:
a) When adding a new stud hole to the bulkhead, the center of the hole must be located a
minimum of one inch away from any existing, non-stiffened hole.
b) The new stud hole must be located such that the terminal lug face, neck, or attaching
hardware will not intrude into the flange bend radius of any edge or stiffened hole.
Refer to MS20659 for terminal lug dimensions.
Verify overbraid terminal bonding by checking resistance between the overbraid and the bulkhead (or the
metallic wing structure for a wing-mounted WXR). Resistance should be less than 2.5 mΩ.
… 398 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GTN 725 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GTN 725 in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info