579857
397
Zoom out
Zoom in
Previous page
1/412
Next page
190-01007-A3 GTN 6XX/7XX AML STC Installation Manual
Rev. 4 Page G-1
Appendix G Lightning Protection
G.1 Lightning Protection in Metal Aircraft
G.1.1 HSDB Weather Radar Interface
When interfacing the GTN 6XX/7XX to an HSDB weather radar (WXR), overbraid is required over any
HSDB cabling in the radome area prior to entering the metal fuselage (or metallic wing). Any wiring for
weather radar configuration modules does not require overbraid as part of this STC. This
section describes how to install the overbraid for the WXR cabling.
The GTN may be interfaced to a weather radar in metal aircraft only. Nonmetallic aircraft
(see Table G-1) must not interface the GTN to a weather radar.
Refer to Appendix E for weather radar interconnect information.
NOTE
Refer to Table G-1 to determine if the aircraft is classified as metal or nonmetallic.
G.1.1.1 Materials Required but Not Supplied
The following materials (or equivalents) are required to install WXR cabling overbraid in the radome
area:
Tinned copper flat braid, 3/4”, QQB575F36T0781 (recommended)
OR
Tinned copper tubular braid, 7/16”, QQB575R30T0437
Electrical tie-down strap, adjustable, MS3367-{1, 2, or 7}-X
Terminal lug, 5/16”, uninsulated, MS20659-131
Terminal stud, 5/16” (or equivalent 5/16” bolt/nut)
NAS970-516 (AN970-516) washer
G.1.1.2 Overbraid Installation Procedure
NOTE
The length of overbraid required is approximately equal to the length of the WXR
cabling in the radome area (measured from the bulkhead or metallic wing entry area
to the WXR R/T connector) plus six inches.
Refer to Figure G-1 and Figure G-2 while completing the following overbraid installation procedure:
1. Remove the backshell from the WXR R/T connector and save for reinstallation. This will allow
the overbraid to slide over the cable without unpinning the connector.
2. Slide the overbraid onto the cable from the WXR R/T to the bulkhead (or grounding provisions at
the metallic wing entry area).
3. Reinstall the WXR R/T connector backshell body.
4. At the WXR R/T end of the overbraid, fold one inch of overbraid back over itself. Position the
overbraid so that the fold will lie under the backshell cover plate, while the overbraid ends will lie
just outside the strain relief bar. Refer to Figure G-1.
5. Install the backshell cover plate and strain relief bar.
397


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GTN 650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GTN 650 in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info