579857
179
Zoom out
Zoom in
Previous page
1/412
Next page
190-01007-A3 GTN 6XX/7XX AML STC Installation Manual
Rev. 4 Page 5-41
5.5.3.6 Main Indicator (Analog)
The Main Indicator diagnostics page allows the CDI connected to the main board (P1001) to be ground
checked and allows the interface to be verified. For the Main Indicator checkout procedure, see
Section 5.6.1.
5.5.3.7 Analog Inputs
The analog inputs diagnostics page displays the bus voltage setting for Lighting Bus 1 and Lighting Bus 2
as well is the input voltage setting for each bus. It also displays synchro heading input diagnostics
information such as heading angle, heading valid status, AC voltage, and AC frequency.
5.5.3.8 Power Stats
The power statistics page displays the number of times the GTN has powered up as well as the total
elapsed operating hours for the GTN.
5.5.3.9 WAAS Diagnostics
The WAAS diagnostics page displays the WAAS engine status, including UTC date/time, current
Lat/Lon, overall navigation status, oscillator temperature, and AGC voltage. This page also allows the
GPS/SBAS engine to be reset.
5.5.3.10 Temps
The Temps diagnostics page displays the current, minimum, maximum, and average board temperatures
for the LED Board, Main Board, Display Interface Board, GPS/SBAS Board, and COM Board.
5.5.3.11 Error Log
The Error log diagnostics page allows the error log to be written to the SD card in the front slot. It also
allows the error log to be cleared.
5.5.3.12 Main Data Inputs
The Main Data Inputs page allows the data on ARINC 429, RS-232, and other electrical inputs to be
monitored. This is used for verifying electrical interfaces during installation and troubleshooting.
Information that is not being received by the GTN is dashed out. The data displayed is prioritized
according to the scheme outlined in Section 2.4.2 if the data is being received on multiple inputs. See
Section 5.6.10 for checkout procedure utilizing this page.
5.5.3.13 VOR/ILS Indicator (Analog)
The VOR/ILS Indicator diagnostics page allows the CDI connected to the NAV board (P1004) to be
ground checked and allows the NAV indicator interface to be verified. See Section 5.6.2 for the ground
check.
5.5.3.14 Clear Config Module
CAUTION
This key should only be touched if the intent is to clear all configuration settings.
Touching the Clear Config Module key opens a confirmation window to reset all of the
settings stored in the configuration module to their defaults.
179


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GTN 650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GTN 650 in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info