579857
111
Zoom out
Zoom in
Previous page
1/412
Next page
190-01007-A3 GTN 6XX/7XX AML STC Installation Manual
Rev. 4 Page 3-31
3.6.5.1.2 TVS2 Fabrication
1. Cut the TVS leads to 0.75+0.00/-0.10 inches on both sides.
2. Crimp and solder each of the four TVS banded side (cathode) leads to their connector specific
sockets (refer to Figure 3-10), and insert into the 4-pin connector with sockets.
3. Install heat shrink around the four TVSs – this will help to hold them in place during the
following steps.
3.6.5.1.3 TVS2 Assembly Build
Refer to Figure 3-11 while completing the following steps.
1. Solder the four leads at the anode (ground) end of the assembly onto a length of 18 AWG wire.
Attach a terminal lug onto the wire end.
2. Attach an appropriately sized piece of heat shrink to cover the soldered TVS leads and four TVS
pieces. A second appropriately sized (larger) piece of heat shrink should then be attached to
shrink over the 4-pin connector with sockets and back over the four TVSs. These two pieces of
heat shrink should overlap along the entire length of the TVSs.
3. Crimp and solder four 18 AWG wires to their connector specific pins, and insert them into the 4-
pin connector with pins.
4. Attach lengths of 18 AWG to both ends of the fuse and fuse holder assembly.
5. Splice the four wires from the connector with pins to one of the wires attached to the fuse
assembly.
6. Attach a terminal lug onto the 18 AWG coming from the other end of the fuse assembly.
7. Connect the two four-pin connectors together.
8. Ensure that the fuse is installed in the fuse holder.
3.6.5.1.4 TVS2 Assembly Polarity Check
Using a multimeter that is set to the diode mode, check conductivity across the entire TVS2 assembly. In
one direction, the meter should read open and in the other direction it should read 2.0 to 2.5 volts. When
installed in the aircraft, the TVS assembly should be oriented so that it does not normally conduct from
power to ground. The meter should indicate open when the red lead is attached to the power bus terminal
lug, and the black lead is attached to the ground terminal lug. The meter should indicate 2.0 to 2.5 volts
when the red lead is attached to the ground terminal lug, and the black lead is attached to the power bus
terminal lug.
3.6.5.1.5 TVS2 Assembly Installation
Refer to Figure E-4 while completing the following steps.
1. Attach the fuse (power) end of the TVS assembly to the power bus at the specific point detailed in
the drawing.
2. Attach the ground end of the TVS2 assembly to aircraft ground.
111


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GTN 650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GTN 650 in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info