579857
48
Zoom out
Zoom in
Previous page
1/412
Next page
GTN 6XX/7XX AML STC Installation Manual 190-01007-A3
Page 2-6 Rev. 4
2.3.2.3 Materials Required but Not Supplied for Optional GMA 35 Installations
Mounting Screws for the GMA 35 (6 minimum – MS24693 Screw, Machine, Flat Countersunk
Head 100°, Cross Recessed with .1380-32 UNC-2A Thread, corrosion resistant steel)
Marker Beacon Antenna approved to TSO-C35( )
Stereo headphone jacks (up to 6), microphone jacks (up to 6), 3.5mm stereo jacks (up to 2), and
insulating washers for all.
2.3.2.4 Materials Required for Lightning Protection (Nonmetallic Aircraft Only)
If additional lightning protection is required for a particular aircraft, the following items may also be
required for the installation. Refer to Appendix G for detailed information regarding which parts are
required for a particular aircraft model.
Applicable to certain nonmetallic aircraft (Except VFR only aircraft). Refer to Appendix G.
Transient Voltage Suppressor 30KPA48A
OR
Transient Voltage Suppressor 15KPA48A
Referred to as TVS1 in the interconnect drawings in Appendix E
Fuse, 3AG Fast-Acting, 4A Littelfuse P/N 0312-004
Referred to as F1 in Figure E-4
Fuse Holder, Inline, Cooper Bussmann P/N HFB
Referred to as F1 in Figure E-4
Four same P/N TVSs (identified as TVS1 above) are combined in accordance with
Section 3.6.5.1.1 to make an assembly referred to TVS2 in Appendix E.
Connector, 4-Pin Plug (socket housing) and Cap (pin housing),
Tyco Electronics P/Ns 1-480424-0 and 1-480426-0 respectively
Referred to as 4 Pin Connector in Section 3.6.5.1.1 and Appendix E.
Sockets, Qty. 4, Tyco Electronics P/N 60617-1 or 60619-1 (Section 3.6.5.1.1)
Pins, Qty. 4, Tyco Electronics, P/N 60618-1 or 60620-1 (Section 3.6.5.1.1)
Tinned Copper Braid, 1/4” nominal flat width, 32 Amp current carrying capacity. Aircraft Spruce
P/N 863. (For GPS/WAAS antenna cable overbraid)
Electrical Tie-Down connector, MS3367-1-X (Section 3.3.1.1)
Aluminum foil tape, 3M P/N 438 (Section 2.4.4.4)
2.3.2.5 Materials Required for Instrument Panel Bonding
If the instrument panel is electrically isolated from the aircraft structure, additional bonding may also be
required for the installation. Refer to Section 3.6.8 for the installation procedure of the instrument panel
bonding strap. The following items are required but not supplied:
Tinned copper flat braid, 3/4”, QQB575F36T0781 (recommended)
OR Tinned copper tubular braid, 7/16”, QQB575R30T0437
Terminal lug, 5/16-inch, uninsulated, MS20659-131
Bolt, AN5-XA
Locking nut, 5/16-inch
Washer, NASM970-516 (AN970-516)
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GTN 650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GTN 650 in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info