Manual Garmin GPSMAP 8700 SERIE (page 32 of 80) (English)

691425

Zoom out

Zoom in

1/80

Setting the Wind Hold Type

Before you can enable the wind hold type, you must connect a

NMEA 2000 or NMEA 0183 wind sensor to the autopilot.

For advanced autopilot configuration, see the installation

instructions included with your autopilot.

From the autopilot screen, select Menu > Autopilot Setup >

Wind Hold Type.

Select Apparent or True.

Engaging Wind Hold

Before you can enable the wind hold type, you must connect a

NMEA 2000 or NMEA 0183 wind sensor to the autopilot.

When the autopilot is in standby mode, select Wind Hold.

Engaging Wind Hold from Heading Hold

Before you can enable the wind hold type, you must connect a

NMEA 2000 or NMEA 0183 wind sensor to the autopilot.

With heading hold engaged, select Menu > Wind Hold.

Adjusting the Wind Hold Angle with the Autopilot

You can adjust the wind hold angle on the autopilot when wind

hold is engaged.

• To adjust the wind hold angle in increments of 1°, select or

• To adjust the wind hold angle in increments of 10°, hold or

Tack and Gybe

You can set the autopilot to perform a tack or gybe while

heading hold or wind hold is engaged.

Tacking and Gybing from Heading Hold

Engage heading hold (Engaging the Autopilot, page 39).

Select Menu.

Select an option.

The autopilot steers your boat through a tack or gybe.

Tacking and Gybing from Wind Hold

Before you can engage wind hold, you must have a wind sensor

installed.

Engage wind hold (Engaging Wind Hold, page 24).

Select Menu.

Select an option.

The autopilot steers your boat through a tack or gybe, and

information about the progress of the tack or gybe appears

on the screen.

Setting a Tack and Gybe Delay

The tack and gybe delay allows you to delay steering a tack and

gybe after you initiate the maneuver.

From the autopilot screen, select Menu > Autopilot Setup >

Sailing Setup > Tack Delay.

Select the length of the delay.

If necessary, select Done.

Enabling the Gybe Inhibitor

NOTE: The gybe inhibitor does not prevent you from manually

performing a gybe using the helm or step steering.

The gybe inhibitor prevents the autopilot from performing a

gybe.

From the autopilot screen, select Menu > Autopilot Setup >

Sailing Setup > Gybe Inhibitor.

Select Enabled.

Adjusting the Autopilot Response

When in sailboat mode, the Response setting allows you to

adjust the rudder gain quickly to account for varying wind

conditions.

From the autopilot screen, select Menu > Response.

Adjust the rudder response.

If you need the rudder to be more responsive and move

quicker, increase the value. If the rudder is moving too much,

decrease the value.

Heading Line and Angle Markers

The heading line is an extension drawn on the map from the

bow of the boat in the direction of travel. Angle markers indicate

relative position from the heading or course over ground, which

are helpful for casting or finding reference points.

Setting the Heading Line and Angle Markers

The heading line is an extension drawn on the map from the

bow of the boat in the direction of travel. Angle markers indicate

relative position from the heading or course over ground, which

are helpful for casting or finding reference points.

You can show the heading line and the course over ground

(COG) line on the chart.

COG is your direction of movement. Heading is the direction the

bow of the boat is pointed, when a heading sensor is connected.

From a chart, select Menu > Layers > My Vessel > Heading

Line.

Angle Markers

If necessary, select Source, and select an option:

• To automatically use the available source, select Auto.

• To use the GPS antenna heading for COG, select GPS

Heading (COG).

• To use data from a connected heading sensor, select

North Reference.

• To use data from both a connected heading sensor and

the GPS antenna, select COG and Heading.

This displays both the heading line and the COG line on

the chart.

Select Display, and select an option:

• Select Distance > Distance, and enter the length of the

line shown on the chart.

• Select Time > Time, and enter the time used to calculate

the distance your boat will travel in the specified time at

your present speed.

Sonar Fishfinder

When properly connected to a transducer, your compatible

chartplotter can be used as a fishfinder. Chartplotter models

without an xsv or xs in their names require a Garmin sounder

module and transducer to display sonar information.

For more information about which transducer is best for your

needs, go to garmin.com/transducers.

Different sonar views can help you view the fish in the area. The

sonar views available vary depending on the type of transducer

and sounder module connected to the chartplotter. For example,

you can view certain Panoptix

™

sonar screens only if you have a

compatible Panoptix transducer connected.

There are four basic styles of sonar views available: a full-

screen view, a split-screen view that combines two or more

views, a split-zoom view, and a split-frequency view that

displays two different frequencies. You can customize the

settings for each view in the screen. For example, if you are

viewing the split-frequency view, you can separately adjust the

gain for each frequency.

If you do not see an arrangement of sonar views to suit your

needs, you can create a custom combination screen (Creating a

New Combination Page, page 4) or a SmartMode layout (Adding

a SmartMode Layout, page 4).

24 Sonar Fishfinder

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 8700 SERIE in the language / languages: English as an attachment in your email.

The manual is 7,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GPSMAP 8700 SERIE

Garmin GPSMAP 8700 SERIE Installation Guide - English - 6 pages

Garmin GPSMAP 8700 SERIE Installation Guide - German - 8 pages

Garmin GPSMAP 8700 SERIE User Manual - German - 92 pages

Garmin GPSMAP 8700 SERIE User Manual - Dutch - 236 pages

Garmin GPSMAP 8700 SERIE Installation Guide - Dutch - 8 pages

Garmin GPSMAP 8700 SERIE User Manual - Dutch - 88 pages

Garmin GPSMAP 8700 SERIE Installation Guide - French - 8 pages

Garmin GPSMAP 8700 SERIE User Manual - French - 90 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Garmin GPSMAP 8700 SERIE Manual

Product: