658280
32
Zoom out
Zoom in
Previous page
1/64
Next page
Transmit Rate: Sets the length of time between sonar pings.
Increasing the transmit rate increases the scroll speed, but it
may also increase self-interference.
Reducing the transmit rate increases the spacing between
transmit pulses and can resolve self-interference.
Transmit Power: Reduces transducer ringing near the surface.
A lower transmit power value reduces transducer ringing, but
can also reduce the strength of the returns.
Filter Width: Defines the edges of the target. A shorter filter
more clearly defines the edges of the targets but may allow
more noise. A longer filter creates softer target edges and
may also reduce noise.
Transducer Diagnostics: Shows details about the transducer.
Flip Left/Right: Switches the
SideVü view orientation from left
to right.
Install Depth: Sets the depth below the water line where the
Panoptix transducer is mounted. Entering the actual depth at
which the transducer is mounted results in a more accurate
visual presentation of what is in the water.
Flipped: Sets the orientation of the
Panoptix sonar view when
the down view transducer is installed with the cables pointing
toward the port side of the boat.
Beam Width: Sets the width of the Panoptix transducer beam.
Narrow beam widths allow you to see deeper and farther.
Wider beam widths allow you to see more coverage area.
Use AHRS: Enables the internal attitude heading and reference
system (AHRS) sensors to detect the installation angle of the
Panoptix transducer automatically. When this setting is
turned off, you can enter the specific installation angle for the
transducer using the Pitch Angle setting. Many forward view
transducers are installed at a 45-degree angle and down
view transducers are installed at a zero-degree angle.
Sonar Recordings
Recording the Sonar Display
NOTE: Not all models support sonar recording.
1
Insert a memory card into the card slot.
2
From a sonar view, select Menu > Sonar Setup >
Sonar
Recording > Record Sonar
.
15 minutes of sonar recording uses approximately 200 MB of
space of the inserted memory card. You can record sonar
until the card reaches capacity.
Stopping the Sonar Recording
Before you can stop recording sonar, you must begin recording
it (Recording the Sonar Display,
page
24).
From a sonar view, select Menu > Sonar Setup > Sonar
Recording > Stop Recording.
Deleting a Sonar Recording
1
Insert a memory card into the card slot.
2
From a sonar view, select Menu > Sonar Setup > Sonar
Recordings
> View Recordings
.
3
Select a recording.
4
Select
Delete.
Playing Sonar Recordings
Before you can play back the sonar recordings, you must
download and install the HomePort
application and record
sonar data onto a memory card.
1
Remove the memory card from the device.
2
Insert the memory card into a card reader attached to a
computer.
3
Open the
HomePort application.
4
Select a sonar recording from your device list.
5
Right-click the sonar recording in the lower pane.
6
Select
Playback.
Radar
WARNING
The marine radar transmits microwave energy that has the
potential to be harmful to humans and animals. Before
beginning radar transmission, verify that the area around the
radar is clear. The radar transmits a beam approximately 12°
above and below a line extending horizontally from the center of
the radar.
When the radar is transmitting, do not look directly at the
antenna at close range; eyes are the most sensitive part of the
body to electromagnetic energy.
When you connect your compatible chartplotter to an optional
Garmin
marine radar, such as a
GMR
Fantom
6
radar or a
GMR
24 xHD, you can view more information about your
surroundings.
The radar transmits a narrow beam of microwave energy as it
rotates to a 360° pattern. When the transmitted energy contacts
a target, some of that energy is reflected back to the radar.
Changing the Radar Mode
1
From a combination screen or SmartMode layout with radar,
select Menu
> Radar Menu > Change Radar
.
2
Select a radar mode.
Transmitting Radar Signals
NOTE:
As a safety feature, the radar enters standby mode after
it warms up. This gives you an opportunity to verify the area
around the radar is clear before beginning radar transmission.
1
With the chartplotter off, connect your radar as described in
the radar installation instructions.
2
Turn on the chartplotter.
If necessary, the radar warms up and a countdown alerts you
when the radar is ready.
3
Select
Radar.
4
Select a radar mode.
A countdown message appears while the radar is starting up.
5
Select Menu >
Transmit Radar
.
Stopping the Transmission of Radar Signals
From a radar screen, select Menu > Radar To Standby.
TIP: Press >
Radar To Standby
from any screen to
quickly stop radar transmission.
Setting Up the Timed Transmit Mode
To help conserve power, you can set up time intervals in which
the radar will transmit and not transmit (standby) signal
transmissions.
NOTE:
This feature is not available in dual radar modes.
1
From a radar screen, select Menu > Radar Options > Timed
Transmit.
2
Select
Timed Transmit to enable the option.
3
Select
Stdby Time, enter the time interval between radar
signal transmissions, and select Done.
4
Select Transmit Time
, enter the duration of each radar
signal transmission, and select Done.
Enabling and Adjusting a Radar No Transmit Zone
You can indicate an area within which the radar scanner does
not transmit signals.
NOTE:
This feature is not available on all radar and chartplotter
models.
24 Radar
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GPSMAP 8424 MFD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 8424 MFD in the language / languages: English as an attachment in your email.

The manual is 2,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GPSMAP 8424 MFD

Garmin GPSMAP 8424 MFD Installation Guide - English - 8 pages

Garmin GPSMAP 8424 MFD Installation Guide - German - 10 pages

Garmin GPSMAP 8424 MFD User Manual - German - 72 pages

Garmin GPSMAP 8424 MFD Installation Guide - Dutch - 10 pages

Garmin GPSMAP 8424 MFD User Manual - Dutch - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info