501975
4
Zoom out
Zoom in
Previous page
1/10
Next page
4 GPSMAP 700 Series Installation Instructions
Installing the Power/Data Cable
The chartplotter comes with a power/data cable that connects the chartplotter to power and to optional
NMEA 0183 devices. If applicable, the power/data cable also connects the chartplotter to a sonar transducer.
The power/data cable does not connect the chartplotter to a NMEA 2000 network. For instructions on
connecting the chartplotter to a NMEA 2000 network, see page 6.
To help make the cable-routing process easier, the locking ring is packaged separately from the cable. If you
install the power/data cable through the bail mount, do not install the locking ring until after all the cables
are routed.
Installing a locking ring on the cable:
1. Route the cable away from sources of electronic interference so that the cable connector is at the
mounting location of the chartplotter.
2. Separate the two halves of the locking ring.
3. Align the two halves of the locking ring over the cable and snap them together.
4. Insert the O-ring into the end of the connector.
GPSMAP 700 Series Power/Data Cable
>
>
>
>
To transducer (if applicable)
Red
Black
Accessory on
Blue
Spare
Spare
Alarm low
Wire Color Wire Function
Power (10–32 Vdc)
Ground
(power and NMEA 0183)
NMEA 0183 port 1 Tx (out)
Brown
Gray
Violet
Green
White
Orange
Yellow
To the GPSMAP 700
series chartplotter
Fuse
3 A
NMEA 0183 port 1 Rx (in)
NMEA 0183 port 2 Tx (out)
NMEA 0183 port 2 Rx (in)
Notes:
Use an AGC/ 3AG - 3 Amp replacement fuse.
If it is necessary to extend the power and ground wires, use 16 AWG wire.
You can wire the cable directly to the battery, or if your boat has an electrical system, you might be able to wire the cable to an unused
holder on the fuse block. If you use the boat fuse block, remove the in-line fuse holder on the power wire of the cable.
Do not cut the transducer cable, because this voids your warranty.
Notice
The maximum input voltage is 32 Vdc. Do not exceed this voltage because this can damage the chartplotter and void the warranty.
NOTE: If you are not connecting the chartplotter to NMEA 0183 devices, use only the red and black wires. The other wires do not have to be
connected for normal operation of the chartplotter. For information on connecting to a NMEA 0183-compatible device, see page 5.
Installing the Locking RingInstalling the Locking Ring
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GPSMAP 751 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 751 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GPSMAP 751

Garmin GPSMAP 751 User Manual - English - 100 pages

Garmin GPSMAP 751 Installation Guide - German - 10 pages

Garmin GPSMAP 751 User Manual - German - 104 pages

Garmin GPSMAP 751 Installation Guide - Dutch - 8 pages

Garmin GPSMAP 751 User Manual - Dutch - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info