Manual Garmin GPSMAP 7416 (page 38 of 62) (English)

657694

Zoom out

Zoom in

1/62

Setting the Power Saver

You can adjust the level of rudder activity.

From the autopilot screen, select Menu > Autopilot Setup >

Power Mode Setup

> Power Saver

Select a percentage.

Selecting a higher percentage reduces rudder activity and

heading performance. The higher the percentage, the more

the course deviates before the autopilot corrects it.

TIP: In choppy conditions at low speeds, increasing the

Power Saver

percentage reduces rudder activity.

Enabling Shadow Drive

™

NOTE: The

Shadow Drive feature is available only on hydraulic

steering systems.

From the autopilot screen, select

Menu > Autopilot Setup >

Shadow Drive

> Enabled

Engaging the Autopilot

When you engage the autopilot, the autopilot takes control of the

helm and steers the boat to maintain your heading.

From any screen, select

Engage.

Your intended heading shows in the center of the Autopilot

screen.

Adjusting the Heading with the Helm

NOTE:

You must enable the Shadow Drive feature before you

can adjust the heading using the helm (

Enabling Shadow

Drive

™

, page 30).

With the autopilot engaged, manually steer the boat.

The autopilot activates

Shadow Drive mode.

When you release the helm and manually maintain a specific

heading for a few seconds, the autopilot resumes a heading

hold at the new heading.

Adjusting the Heading with the Chartplotter in Step

Steering Mode

Before you can steer your boat using the keys at the bottom of

the autopilot screen, you must engage the autopilot (Engaging

the Autopilot, page 30).

• Select

<1° or 1°> to initiate a single 1° turn.

• Select

<<10° or 10°>> to initiate a single 10° turn.

• Hold

<1° or 1°> to initiate a rate-controlled turn.

The boat continues to turn until you let go of the key.

• Hold

<<10° or 10°>> to initiate a sequence of 10° turns.

Steering Patterns

WARNING

You are responsible for the safe operation of your boat. Do not

begin a pattern until you are certain that the water is clear of

obstacles.

The autopilot can steer the boat in preset patterns for fishing,

and it can also perform other specialty maneuvers such as U-

turns and Williamson turns.

Following the U-Turn Pattern

You can use the u-turn pattern to turn the boat around 180

degrees and maintain the new heading.

From the autopilot screen, select Menu > Pattern Steering >

U-Turn.

Select

Engage Port or Engage Starboard.

Setting Up and Following the Circles Pattern

You can use the circles pattern to steer the boat in a continuous

circle, in a specified direction, and at a specified time interval.

From the autopilot screen, select Menu > Pattern Steering >

Circles.

If necessary, select

Time, and select a time for the autopilot

to steer one complete circle.

Select Engage Port or

Engage Starboard.

Setting Up and Following the Zigzag Pattern

You can use the zigzag pattern to steer the boat from port to

starboard and back, over a specified time and angle, across

your present heading.

From the autopilot screen, select Menu > Pattern Steering >

Zigzag.

If necessary, select

Amplitude, and select a degree.

If necessary, select

Period, and select a length of time.

Select

Engage Zigzag.

Following the Williamson Turn Pattern

You can use the Williamson turn pattern to steer the boat

around with the intent of running alongside the location where

the Williamson turn pattern was initiated. The Williamson turn

pattern can be used in man overboard situations.

From the autopilot screen, select Menu

> Pattern Steering >

Williamson Turn

Select

Engage Port or Engage Starboard.

Following an Orbit Pattern

You can use the orbit pattern to steer the boat in a continuous

circle around the active waypoint. The size of the circle is

defined by your distance from the active waypoint when you

begin the orbit pattern.

From the autopilot screen, select Menu >

Pattern Steering >

Orbit

Select

Engage Port or Engage Starboard.

Setting Up and Following the Cloverleaf Pattern

You can use the cloverleaf pattern to steer the boat to

repeatedly pass over an active waypoint. When you begin the

cloverleaf pattern, the autopilot drives the boat toward the active

waypoint and begins the cloverleaf pattern.

You can adjust the distance between the waypoint and the

location where the autopilot turns the boat for another pass over

the waypoint. The default setting turns the boat at a range of

1000 ft. (300 m) from the active waypoint.

From the autopilot screen, select Menu

> Pattern Steering >

Cloverleaf

If necessary, select Length, and select a distance.

Select

Engage Port or Engage Starboard.

Setting Up and Following a Search Pattern

You can use the search pattern to steer the boat in increasingly

larger circles outward from the active waypoint, forming a spiral

pattern. When you begin the search pattern, the autopilot drives

the boat to the active waypoint and begins the pattern.

You can adjust the distance between each circle in the spiral.

The default distance between circles is 50 ft. (20 m).

From the autopilot screen, select Menu > Pattern Steering >

Search.

If necessary, select

Search Spacing, and select a distance.

Select

Engage Port or Engage Starboard.

Cancelling a Steering Pattern

• Physically steer the boat.

NOTE: Shadow Drive must be enabled to cancel a steering

pattern by physically steering the boat.

• Select or to cancel a pattern using step steering mode.

• Select

Standby.

30 Autopilot

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 7416 in the language / languages: English as an attachment in your email.

The manual is 2,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GPSMAP 7416

Garmin GPSMAP 7416 Installation Guide - English - 8 pages

Garmin GPSMAP 7416 Installation Guide - German - 8 pages

Garmin GPSMAP 7416 User Manual - German - 72 pages

Garmin GPSMAP 7416 Installation Guide - Dutch - 8 pages

Garmin GPSMAP 7416 User Manual - Dutch - 68 pages

Garmin GPSMAP 7416 Installation Guide - French - 8 pages

Garmin GPSMAP 7416 User Manual - French - 70 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Garmin GPSMAP 7416 Manual

Product: