522235
96
Zoom out
Zoom in
Previous page
1/104
Next page
86
Appendix H
Unit Installation
The GPSMAP 182/182C/232 with external antenna can be fl ush mounted on a fl at panel of .08-
.52” thickness using the cam lobe feature on its gimbal mounting bracket. When fl ush mounting the
GPSMAP 182/182C/232, be sure to choose an appropriately sized location for the unit (see unit dimen-
sions pg. 83) and leave 1.25” (32mm) clearance below the data card slot for inserting/removing data
cards. For fl ush mounting the GPSMAP 232 unit, skip to the next set of instructions.
To ush mount the GPSMAP 182/182C unit using the gimbal mounting bracket:
1. Cut a 4.33”W x 4.33”H (110 x 110 mm) hole in the panel.
2. Place the GPSMAP 182/182C/232 into the hole from the front until the fl ange rests against the
mounting surface.
3. From the back of the panel, loosely attach the bracket such that the slot in the ratchet area points
away from the mounting panel (fi gure 1).
4. Rotate the bracket downward until the panel is pinched tightly between the unit’s fl ange and
bracket lobe (fi gure 1).
5. Tighten the knobs and connect the power/data and antenna cables. Note: if the panel is too thick
to allow use of the supplied knobs, two M6 screws may be used to secure the bracket.
The GPSMAP 182/182C/232, with external antenna, may also be fl ush mounted on a fl at panel
using its existing mounting bracket.
To ush mount the GPSMAP 182/182C/232 unit:
1. Remove the four M5 screws from the back of the unit and remove the mounting bracket.
2. Using the mounting bracket as a template, outline the center relief area and mark the location of
the four screw holes centers on your bulkhead or other surface (fi gure 2).
3. Cut the relief hole from the panel and drill the four 0.20” (5.08 mm) screw holes.
4. Place the GPSMAP 182/182C/232 into the relief hole until it rests fl ush against the mounting
surface.
5. Secure the unit to the mounting surface using the M5 screws. Do not try to force the screws deeper
into the holes than the holes will allow. For thick mounting surfaces, insert the M5 screws directly
thru the drilled holes (fi gure 3). For thin panels, place the mounting bracket on the back side of the
panel for more support. Connect the power/data and antenna cables.
Figure 1
Figure 2
Figure 3
Pull gimbal bracket down
until cam lobe contacts
surface.
182C Manual Part 2.indd 86 6/4/2003, 2:54:32 PM
96


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GPSMAP 182C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 182C in the language / languages: English as an attachment in your email.

The manual is 2,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info