522233
99
Zoom out
Zoom in
Previous page
1/109
Next page
Mounting the GPSMAP 172/172C Unit
The GPSMAP 172/172C’s compact, waterproof case is suitable for mounting in exposed locations
or at the nav station. The unit comes with a single-knob tilt & swivel bracket that can be used for surface
or overhead mounting. When choosing a location for the display unit, make sure you consider the
following conditions:
There should be at least a 3” (7 cm) clearance behind the case to allow connection of the
antenna (external antenna only), power/data cables.
The mounting surface should be heavy enough to support the unit and protect it from excessive
vibration and shock.
For GPSMAP 172/172C unit’s with the built-in internal antenna, it should be mounted in a location
that has the clearest, most unobstructed view of the sky in all directions to ensure the best reception.
Avoid mounting the unit where it is blocked by the boat’s superstructure, a radar arch, or mast.
The temperature range for the GPSMAP 172/172C is 5°F to 158°F (-15°C to 55°C).
Extended exposure to temperatures exceeding this range (in storage or operating
conditions) may cause failure of the LCD screen. This type of failure and related conse
-
quences are NOT covered by the manufacturer’s limited warranty.
To swivel mount the GPSMAP 172/172C display:
Tools (not included) — Drill, Screwdriver (Phillips or Standard), three #8 (4mm) pan head machine
bolts with matching nuts and washers and a 5/32” (5mm) drill bit, OR three #8 pan head self-tap
-
ping screws and an appropriately-sized drill bit for drilling starter holes. Always wear safety goggles,
ear protection, and a dust mask when drilling, cutting or sanding.
1. Using the swivel base as a template, mark the location of the three holes that are used to secure
the bracket to the mounting surface.
2. If securing the base with machine bolts, drill three 5/32” (5mm) holes at the locations you marked.
OR, if securing the base with self-tapping screws, drill starter holes at the locations you marked.
Starter holes should generally be no deeper than half the screw length.
3. Secure the swivel base with three bolts or screws. DO NOT OVERTIGHTEN.
4. Place the rest of the mount over the swivel base and secure with the short knob.
Secure the base and attach the mount
The swivel base is designed to be secured using a pan
head screw or machine bolt. If you use a screw with a
countersunk head, you risk damaging the Mounting
Base.
OK
89
Appendix G
Unit Installation
99


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GPSMAP 172C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 172C in the language / languages: English as an attachment in your email.

The manual is 3,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info