657710
37
Zoom out
Zoom in
Previous page
1/60
Next page
Learn to operate the autopilot on calm and hazard-free open
water.
Use caution when operating the autopilot near hazards in the
water, such as docks, pilings, and other boats.
The autopilot system continuously adjusts the steering of your
boat to maintain a constant heading (heading hold). The system
also allows manual steering and several modes of automatic-
steering functions and patterns.
Opening the Autopilot Screen
Before you can open the autopilot screen, you must have a
compatible autopilot installed and configured.
Select
A/V, Gauges, Controls >
Autopilot
.
Autopilot Bar
À
Actual heading
Á
Intended heading (heading the autopilot is steering toward)
Â
Actual heading (when in standby mode)
Intended heading (when engaged)
Adjusting the Step Steering Increment
1
From the Autopilot screen, select MENU
> Autopilot Setup >
Step Turn Size
.
2
Select an increment.
Setting the Power Saver
You can adjust the level of rudder activity.
1
From the autopilot screen, select MENU
> Autopilot Setup >
Power Mode Setup > Power Saver
.
2
Select a percentage.
Selecting a higher percentage reduces rudder activity and
heading performance. The higher the percentage, the more
the course deviates before the autopilot corrects it.
TIP: In choppy conditions at low speeds, increasing the
Power Saver
percentage reduces rudder activity.
Enabling Shadow Drive
NOTE: The
Shadow Drive feature is available only on hydraulic
steering systems.
From the autopilot screen, select
MENU
> Autopilot Setup >
Shadow Drive > Enabled
.
Engaging the Autopilot
When you engage the autopilot, the autopilot takes control of the
helm and steers the boat to maintain your heading.
From any screen, select
Engage.
Your intended heading shows in the center of the Autopilot
screen.
Adjusting the Heading with the Helm
NOTE:
You must enable the Shadow Drive feature before you
can adjust the heading using the helm (
Enabling Shadow
Drive
,
page
29).
With the autopilot engaged, manually steer the boat.
The autopilot activates Shadow Drive mode.
When you release the helm and manually maintain a specific
heading for a few seconds, the autopilot resumes a heading
hold at the new heading.
Adjusting the Heading with the Chartplotter in Step
Steering Mode
Before you can steer your boat using the keys at the bottom of
the autopilot screen, you must engage the autopilot (Engaging
the Autopilot,
page
29).
Select
<1° or 1°> to initiate a single 1° turn.
Select <<10° or 10°>> to initiate a single 10° turn.
Hold
<1° or 1°> to initiate a rate-controlled turn.
The boat continues to turn until you let go of the key.
Hold
<<10° or 10°>> to initiate a sequence of 10° turns.
Steering Patterns
WARNING
You are responsible for the safe operation of your boat. Do not
begin a pattern until you are certain that the water is clear of
obstacles.
The autopilot can steer the boat in preset patterns for fishing,
and it can also perform other specialty maneuvers such as U-
turns and Williamson turns.
Following the U-Turn Pattern
You can use the u-turn pattern to turn the boat around 180
degrees and maintain the new heading.
1
From the autopilot screen, select MENU > Pattern Steering
> U-Turn.
2
Select
Engage Port or Engage Starboard.
Setting Up and Following the Circles Pattern
You can use the circles pattern to steer the boat in a continuous
circle, in a specified direction, and at a specified time interval.
1
From the autopilot screen, select MENU > Pattern Steering
>
Circles
.
2
If necessary, select
Time, and select a time for the autopilot
to steer one complete circle.
3
Select
Engage Port or Engage Starboard.
Setting Up and Following the Zigzag Pattern
You can use the zigzag pattern to steer the boat from port to
starboard and back, over a specified time and angle, across
your present heading.
1
From the autopilot screen, select MENU >
Pattern Steering
> Zigzag
.
2
If necessary, select
Amplitude, and select a degree.
3
If necessary, select Period
, and select a length of time.
4
Select
Engage Zigzag.
Following the Williamson Turn Pattern
You can use the Williamson turn pattern to steer the boat
around with the intent of running alongside the location where
the Williamson turn pattern was initiated. The Williamson turn
pattern can be used in man overboard situations.
1
From the autopilot screen, select MENU
> Pattern Steering
> Williamson Turn
.
2
Select Engage Port or
Engage Starboard.
Following an Orbit Pattern
You can use the orbit pattern to steer the boat in a continuous
circle around the active waypoint. The size of the circle is
defined by your distance from the active waypoint when you
begin the orbit pattern.
1
From the autopilot screen, select MENU > Pattern Steering
> Orbit.
2
Select
Engage Port or Engage Starboard.
Autopilot 29
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GPSMAP 1022 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 1022 in the language / languages: English as an attachment in your email.

The manual is 2,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GPSMAP 1022

Garmin GPSMAP 1022 Installation Guide - English - 8 pages

Garmin GPSMAP 1022 Installation Guide - German - 8 pages

Garmin GPSMAP 1022 User Manual - German - 70 pages

Garmin GPSMAP 1022 User Manual - Dutch - 66 pages

Garmin GPSMAP 1022 Installation Guide - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info