Manual Garmin GPSMAP 1022 (page 31 of 60) (English)

657710

Zoom out

Zoom in

1/60

When smoothing is set to high, more of the low-level noise

remains than when using the interference control, but the

noise is more subdued because of averaging. Smoothing can

remove speckle from the bottom. Smoothing and interference

work well together to eliminate low-level noise. You can

adjust the interference and smoothing settings incrementally

to remove undesirable noise from the display.

Surface Noise: Hides surface noise to help reduce clutter.

Wider beam widths (lower frequencies) can show more

targets, but can generate more surface noise.

TVG: Adjusts the time varying gain, which can reduce noise.

This control is best used for situations when you want to

control and suppress clutter or noise near the water surface.

It also allows for the display of targets near the surface that

are otherwise hidden or masked by surface noise.

Sonar Appearance Settings

From a sonar view, select MENU > Sonar Setup >

Appearance.

Color Scheme: Sets the color scheme and color gain.

Overlay Data: Sets the data shown on the sonar screen.

A-Scope: Displays a vertical flasher along the right side of the

screen that shows instantaneously the range to targets along

a scale.

Depth Line: Shows a quick-reference depth line.

Edge: Highlights the strongest signal from the bottom to help

define the hardness or softness of the signal.

Pic. Advance: Allows the sonar picture to advance faster by

drawing more than one column of data on the screen for

each column of sounder data received. This is especially

helpful when you are using the sounder in deep water,

because the sonar signal takes longer to travel to the water

bottom and back to the transducer.

The 1/1 setting draws one column of information on the

screen per sounder return. The 2/1 setting draws two

columns of information on the screen per sounder return, and

so on for the 4/1 and 8/1 settings.

Sonar Alarm Settings

NOTE: Some settings require external accessories.

Select Settings >

Alarms > Sonar

Shallow Water: Sets an alarm to sound when the depth is less

than the specified value.

Deep Water: Sets an alarm to sound when the depth is greater

than the specified value.

Water Temp.: Sets an alarm to sound when the transducer

reports a temperature that is 2°F (1.1°C) above or below the

specified temperature.

Contour: Sets an alarm to sound when the transducer detects a

suspended target within the specified depth from the surface

of the water and from the bottom.

Fish: Sets an alarm to sound when the device detects a

suspended target.

• sets the alarm to sound when fish of all sizes are

detected.

• sets the alarm to sound only when medium or large

fish are detected.

• sets the alarm to sound only when large fish are

detected.

Advanced Sonar Settings

From a sonar view, select MENU > Sonar Setup > Advanced.

Transmit: Stops the transducer from transmitting.

Shift: Allows you to set the depth range on which the sonar is

focused. This allows you to zoom in a higher resolution in the

focused depth.

When using shift, bottom tracking may not work effectively,

because the sonar looks for data within the depth range of

the focused area, which may not include the bottom. Using

shift also can impact the scroll speed, because data outside

the depth range of the focused area is not processed, which

reduces the time required to receive and display the data.

You can zoom in to the focused area, which enables you to

evaluate target returns more closely at a higher resolution

than just zooming alone.

Echo Stretch: Adjusts the size of the echoes on the screen to

make it easier to see separate returns on the screen.

When targets are difficult to see, echo stretch makes the

target returns more pronounced and easier to see on the

screen. If the echo stretch value is too high, the targets blend

together, and if the value is too low, the targets might be

small and difficult to see.

You can use echo stretch and filter width together to obtain

the preferable resolution and noise reduction. With echo

stretch and filter width set to low, the display has the highest

resolution, but is the most susceptible to noise. With echo

stretch set to high and filter width set to low, the display has a

lower resolution, but has wider targets. With echo stretch and

filter width set to high, the display has the lowest resolution,

but is the least susceptible to noise. It is not recommended to

set echo stretch to low and filter width to high.

Bottom Track.: Sets the frequency used for determining depth.

The bottom tracking control allows you to select the specific

channel that is used to track the bottom. For example, you

can set the bottom tracking for the low frequency for deep

water operation.

Temp. Source: Sets the channel for the water temperature log

when more than one water-temperature sensor or

temperature-capable transducer is connected.

Transducer Installation Settings

From a sonar view, select MENU > Sonar Setup > Installation.

Transmit Rate: Sets the length of time between sonar pings.

Increasing the transmit rate increases the scroll speed, but it

may also increase self-interference.

Reducing the transmit rate increases the spacing between

transmit pulses and can resolve self-interference.

Transmit Power: Reduces transducer ringing near the surface.

A lower transmit power value reduces transducer ringing, but

can also reduce the strength of the returns.

Filter Width: Defines the edges of the target. A shorter filter

more clearly defines the edges of the targets but may allow

more noise. A longer filter creates softer target edges and

may also reduce noise.

Transducer Diagnostics: Shows details about the transducer.

Flip Left/Right: Switches the

SideVü view orientation from left

to right.

Install Depth: Sets the depth below the water line where the

Panoptix

transducer is mounted. Entering the actual depth at

which the transducer is mounted results in a more accurate

visual presentation of what is in the water.

Flipped: Sets the orientation of the Panoptix sonar view when

the down view transducer is installed with the cables pointing

toward the port side of the boat.

Beam Width: Sets the width of the Panoptix transducer beam.

Narrow beam widths allow you to see deeper and farther.

Wider beam widths allow you to see more coverage area.

Use AHRS: Enables the internal attitude heading and reference

system (AHRS) sensors to detect the installation angle of the

Panoptix

transducer automatically. When this setting is

turned off, you can enter the specific installation angle for the

transducer using the Pitch Angle setting. Many forward view

Sonar 23

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 1022 in the language / languages: English as an attachment in your email.

The manual is 2,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GPSMAP 1022

Garmin GPSMAP 1022 Installation Guide - English - 8 pages

Garmin GPSMAP 1022 Installation Guide - German - 8 pages

Garmin GPSMAP 1022 User Manual - German - 70 pages

Garmin GPSMAP 1022 User Manual - Dutch - 66 pages

Garmin GPSMAP 1022 Installation Guide - French - 8 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Garmin GPSMAP 1022 Manual

Product: