583716

Garmin GPSCOM 170 Manual

79
Zoom out
Zoom in
Previous page
1/88
Next page
Accuracy has been Degraded—The accura-
cy of the receiver has been degraded beyond
500 meters due to poor satellite geometry or
data quality. You should check other naviga-
tional sources to verify the position indicated.
Active Waypoint Can’t Be Deleted—You
have attempted to change the ‘Active To’ or
‘Active From’ waypoint. Clear the active route
or GOTO before making your changes.
Already Exists—The name you are entering
already exists in memory.
Battery Power is Low—The Ni-Cad battery
is low and should be recharged.
Battery Power is too Low to Transmit—
Battery power is too low to allow transmitting.
COM Failed—The VHF com has failed. Take
the unit to an authorized service center.
GPS and COM Turned Off—The GPS and
Com functions are turned off due to low bat-
tery voltage.
Leg Not Smoothed—The upcoming route leg
is too short for smooth waypoint transitions.
Need 2D Altitude—The unit needs altitude
input in order to start and/or continue 2D nav-
igation.
No DGPS Position—Not enough data is
available to compute a DGPS position.
No RTCM Input—
The beacon receiver is
improperly connected or baud rates do not
match.
Oscillator Needs Adjustment—The unit has
detected excessive drift in its internal crystal
oscillator which may result in longer acquisi-
tion time. Take the unit to an authorized ser-
vice center.
Poor GPS Coverage—The unit cannot
acquire the necessary number of satellites to
compute a position. Try another location with
a clearer view of the sky.
Power Down and Re-init—The unit is not
able to calculate a position due to abnormal
satellite conditions. Turn the unit off and veri-
fy the last position shown by other means. Try
the unit again later, possibly in a different loca-
tion.
Read Only Mem has Failed—The perma-
nent memory has failed and the unit is not
operable. Take the unit to an authorized ser-
vice center.
Received an Invalid WPT—A waypoint was
received during upload transfer that has an
invalid identifier.
Route Waypoint Can’t be Deleted—The
waypoint you are trying to delete is part of a
route. Delete the waypoint from the route
before removing it from memory.
Receiver has Failed—A failure in receiver
hardware has been detected. If this message
persists, take the unit to an authorized dealer.
Route is Full—You have attempted to add
more than 30 waypoints to a route.
The GPSCOM 170 uses a flashing on-screen message
indicator to alert you to important information. Whenever the
message indicator appears, press
P
to view the message
page. There are two types of messages: temporary alerts and
condition alerts. Temporary alerts are cleared from the message
page after viewing, while condition alerts remain until the con-
dition has been resolved. Pay careful attention to all messages
for your own safety.
Messages
APPENDIX E
74
170 manual pages rev D 9/21/98 9:23 AM Page 74
… 79 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GPSCOM 170 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSCOM 170 in the language / languages: English as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info