39882

Garmin GPS 120XL Manual

64
Zoom out
Zoom in
Previous page
1/72
Next page
Messages &
Time Offsets
APPENDIX C
60
Active WPT Can’t be Deleted—You have attempted to change the “active to” or “active
from” waypoint. Clear the active route or GOTO before making your changes.
Accuracy has been Degraded—The accuracy of the GPS 120XL has been degraded
beyond 500 meters due to poor satellite geometry or data quality. You should check other
navigational sources to verify the position indicated.
Already Exists—The name you are entering already exists in the GPS 120XL’s memory.
Approaching—You are one minute away from reaching a destination waypoint.
Battery Power is Low—The batteries are low and should be replaced.
No DGPS Position—Not enough data is available to compute a DGPS position.
No RTCM Input—
Beacon receiver is improperly connected or baud rates do not match.
Poor GPS Coverage—The GPS 120XL cannot acquire the necessary number of satellites to
compute a position. Try another location with a clearer view of the sky.
Power Down and Re-init—The GPS 120XL is not able to calculate a position due to
abnormal satellite conditions. Turn the unit off and verify the last position shown by other
means. Try the unit again later, possibly in a different location.
Read Only Mem has Failed—The permanent memory has failed and the unit is not oper-
able. Take your unit to an authorized GARMIN dealer for repairs.
Received an Invalid WPT—A waypoint was received during upload transfer that has an
invalid identifier.
Receiver has Failed—A failure in receiver hardware has been detected. If this message
persists, do not use the unit and take it to an authorized dealer for repair.
Route is Full—You have attempted to add more than 30 waypoints to a route.
Route is not Empty—You have attempted to copy into a route already in use.
Route Waypoint Can’t be Deleted—The waypoint you are trying to delete is part of a
route. Delete the waypoint from the route before removing it from memory.
Route Waypoint was Deleted—A route waypoint entered does not exist in the database
and has been deleted from the route.
RTCM Input has Failed—DGPS data being received has been lost. You are no longer
receiving the beacon signal.
Searching the Sky—The GPS 120XL is in searching the sky for almanac data or the unit is
in AutoLocate
TM
mode.
The GPS 120XL uses a flashing on-screen message to
alert you to important information. Whenever the message
indicator appears, press the PAGE key to view the message
page. There are two types of messages: temporary alerts
and condition alerts. Temporary alerts are cleared from the
message page after viewing, while condition alerts remain
on the message page until the condition has been resolved.
Pay careful attention to all messages for your own safety.
120XL Man RevB 7/10/98 10:55 AM Page 60
… 64 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GPS 120XL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPS 120XL in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info