691469
7
Zoom out
Zoom in
Previous page
1/12
Next page
Configuring the Beeper
You can configure the beeper to sound when the keys are
pressed.
Select > SETUP > SYSTEM > BEEPER.
Configuring the Position Format
NOTE: Do not change the position format or the map datum
unless you are using a map or chart that specifies a different
position format.
1
Select > SETUP > SYSTEM > GPS POSITION.
2
Select an option:
To change the position format in which a reading appears,
select POSITION FORMAT.
To change the coordinate system on which the map is
structured, select MAP DATUM.
Display Settings
Select > SETUP > DISPLAY.
BACKLIGHT: Sets the backlight brightness.
COLOR: Sets the screen color.
NETWORK SHARING: Shares color, backlight, and beeper
settings with devices across the NMEA 2000 network.
Configuring Data Sources
Sensors connected to your instrument provide data, such as
wind or speed information, and can be configured through your
instrument. See the owner's manual for each sensor for more
information.
1
Select > SETUP > DATA SOURCES.
2
Select a data category.
3
If more than one sensor on the boat provides data from the
category, select a sensor to configure.
4
Select a configuration option, and configure the setting.
Resolving a Combined Network
When the device is turned on, it can detect when it has been
synchronized with instruments on another network. This can
happen if the device has previously been installed on another
vessel and synchronized with instruments on the other vessel's
network. If the settings are not restored to the factory default
values (Restoring Profiles to their Default Settings, page 1), the
device detects a conflict that must be resolved.
1
Select > SETUP > COMBINED NETWORKS
DETECTED.
2
Select an option:
To synchronize existing instruments on the network to the
device, select NO.
To synchronize the device to existing instruments on the
network, select YES.
Keypad Operation
The keypad can control all of the compatible marine instruments
on your NMEA 2000 network. All compatible marine instruments
must be connected to the same NMEA 2000 network, and you
can configure the order in which they are controlled.
NOTE: The keypad is not compatible with all Garmin marine
instruments. For a complete list of compatible instruments, go to
www.garmin.com/GNXkeypad.
Button Function
Select to cycle backlight levels on the marine
instruments and keypads.
Hold to place the marine instruments and keypads into
sleep mode.
À
through
Ã
Presets. Select to make all displays switch to a
configured preset page.
Select to switch the marine instrument you control using
the keypad.
Select to cycle the pages on the selected marine
instrument.
Setting up an Instrument for Use with the
Keypad
All compatible marine instruments you need to control with the
keypad must be connected to the same NMEA 2000 network as
the keypad.
You should perform this procedure for each compatible
instrument you add to the NMEA 2000 network.
1
On a compatible marine instrument connected to the same
NMEA 2000 network as the keypad, select > SETUP >
REMOTE KEYPAD SETUP.
NOTE: If COMBINED NETWORKS DETECTED is shown
instead of REMOTE KEYPAD SETUP, the combined network
must be resolved before you can control the instrument with
the keypad (Resolving a Combined Network, page 3).
2
Select YES to enable keypad control on the instrument.
3
Repeat steps 1 through 2 for each additional compatible
instrument you need to control with the keypad.
Setting up the Keypad Display Order
You can configure how the keypad cycles through connected
marine instruments with the buttons.
1
On a compatible marine instrument connected to the same
NMEA 2000 network as the keypad, select > SETUP >
REMOTE KEYPAD SETUP > SET UP DISPLAY ORDER.
The device scans the network for other connected
instruments.
NOTE: The location of the device in the current display order
is shown to the right of the SET UP DISPLAY ORDER menu
item. For example, if the device is second in a series of four
devices, 2:4 is shown in the menu.
2
Select an option:
If a correct number of connected instruments is shown,
select CONTINUE.
If an incorrect number of connected instruments is shown,
check the power and connections of all compatible
instruments, and select RETRY.
Keypad Operation 3
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GNX 130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GNX 130 in the language / languages: English as an attachment in your email.

The manual is 1,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GNX 130

Garmin GNX 130 Installation Guide - English - 2 pages

Garmin GNX 130 Installation Guide - German - 4 pages

Garmin GNX 130 User Manual - German - 14 pages

Garmin GNX 130 Installation Guide - Dutch - 4 pages

Garmin GNX 130 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info