584000
26
Zoom out
Zoom in
Previous page
1/124
Next page
Page 3-6 400 SERIES INSTALLATION MANUAL
Page Rev L P/N 190-00140-02
Table 3-2. Recommended Crimp Tools (or equivalent)
Connector
Type
High Density Standard Density
Wire Gauge 22-28 AWG 18 AWG 20-24 AWG
Hand
Crimping
Tool
Positioner Insertion/
Extraction
Tool
Positioner Insertion/
Extraction
Tool
Positioner Insertion/
Extraction
Tool
Military P/N M22520/2-01 M22520/2-09 M81969/1-04 N/A M81969/1-02 M22520/2-08 M81969/1-02
Positronic 9507 9502-3 M81969/1-04 9502-11 M81969/1-02 9502-5 M81969/1-02
ITT Cannon 995-0001-
584
995-0001-
739
N/A N/A N/A 995-0001-
604
980-2000-
426
AMP 601966-1 601966-6 91067-1 N/A N/A 601966-5 91067-2
Daniels AFM8 K42 M81969/1-04 K774 M81969/1-02 K13-1 M81969/1-02
Astro 615717 615725 M81969/1-04 N/A M81969/1-02 615724 M81969/1-02
NOTES
1. Insertion/extraction tools from ITT Cannon are all plastic; others are plastic with metal tip.
2. Non-Garmin part numbers shown are not maintained by Garmin and consequently are subject
to change without notice.
3. Alternate contacts for 18 AWG wire: As an alternative to the Positronic contacts listed (and
provided in the installation kit), the installer may use contacts made by ITT Cannon under P/N
031-1007-001. These contacts require the use of a different crimp tool positioner than shown
in the table, with the part numbers as follows: Daniels P/N K250, Astro P/N 616245, or ITT
Cannon P/N 980-0005-722.
4. For the card-edge connector pin contacts, use AMP part number 90272-1 or equivalent
crimping tool.
3.7 RACK INSTALLATION
1. The back plate of the rack may optionally be removed for ease of mounting in the aircraft
panel. To do so, remove the two #4-40 screws, tilt the back plate away from the tray, and then
slide the back plate to the side.
2. Figures 3-3, 3-4 and 3-5, starting on pages 3-11, 3-13, and 3-15, show outline dimensions for
the aviation rack for the various 400 Series units. Install the rack in a rectangular 6.320” x
2.700” hole (or gap between units) in the instrument panel (refer to Figure 3-9, page 3-23).
The lower-front lip of the rack should be flush with, or extend slightly beyond, the finished
aircraft panel.
CAUTION
If the front lip of the mounting rack is behind the surface of the aircraft panel,
the 400 Series unit connectors may not fully engage.
Make sure that no screw heads or other obstructions prevent the unit from fully engaging in the
rack (refer to the “Connector Engagement Test,” section 5.3.1, page 5-15). Exercise caution
when installing the rack into the instrument panel. The rack is designed to facilitate removal of
the 400 Series for use in Demo Mode outside the aircraft. Deformation of the rack may make it
difficult to install and remove the 400 Series unit.
3. Install the rack in the aircraft panel using six #6-32 flat head screws and six self-locking nuts.
The screws are inserted from the inside through the holes in the sides of the rack.
4. If the back plate was previously removed (see step #1), replace the back plate by positioning
the tabs on the back plate in the slots of the left side of the rack (viewing it from the cockpit)
and attaching it by replacing the two #4-40 screws.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GNC 420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GNC 420 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info