Manual Garmin GC 200 (page 2 of 18) (English, German, Danish, French, Italian, Swedish, Spanish, Norwegian)

691894

Zoom out

Zoom in

1/18

™

200 IP Marine Camera

Installation Instructions

Mounting Considerations

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

You can mount the camera upside-down or sideways. You can

reverse the camera image to use in rearview mode. See your

chartplotter owner's manual for instructions.

NOTE: You must update your chartplotter software to setup and

view the camera feed on your chartplotter.

• You must mount the camera in a location where it is not

submerged, does not present a hazard in doorways or

walkways, and cannot be damaged by docks, pilings, or other

pieces of equipment.

• You should mount the camera in a location strong enough to

support the weight of the device and where you can remove

the camera.

• You should mount the camera so the LED is visible and the

cables can be connected easily.

• To avoid interference with a magnetic compass, do not

mount the camera closer to a compass than the compass-

safe distance value listed in the product specifications.

• You should test the camera in the selected location before

you permanently mount the camera.

• You can use the Garmin

Power Module to help make the

installation easier. The Power Module uses a single camera

cable instead of separate power and ethernet cables. This is

especially beneficial when the camera is located far away

from other electronics, such as near the bow or on a mast.

Tools Needed

• Drill and 2 mm (

in.) drill bit

• Pozidriv

screwdriver

Mounting the Camera

Secure the template to the mounting location.

Using a 2 mm (

in.) drill bit, drill the pilot holes.

Using the included hex wrench, loosen the screw in the side

of the camera base.

Remove the base from the camera body.

Feed the camera cables through the camera base, or through

one of the cable channels.

Align the camera base with the pilot holes, and secure the

camera base with the washers and screws .

Attach the camera to the base, and tighten the screw in

the camera base.

Connect the camera cables.

Align the slots on the camera base with the collar lugs ,

and turn the collar until it locks.

Connection Considerations

Connection Diagram with Direct Power

™

200 marine IP camera

Garmin Marine Network cable small connector (included)

Garmin Marine Network Adapter Cable small to large (included)

9 to 18 Vdc power source (not included)

NOTICE

To avoid permanently damaging the camera, do not connect the

camera directly to a 24 Vdc system. You must use a Garmin Power

Module when connecting to a 24 Vdc system.

1 A fast-acting fuse (required, not included)

NOTICE

You must connect the power wire through a 1 A fast-acting fuse

(not included). Without a fuse, the device can malfunction.

Garmin chartplotter (not included)

Connection Diagram with a Garmin Power Module

GC 200 marine IP camera

Garmin Marine Network cable small connector

Power module (010-12527-00, not included)

In-line switch (not included)

9 to 32 Vdc power source (not included)

Chartplotter (not included)

2 Installation Instructions

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GC 200 in the language / languages: English, German, Danish, French, Italian, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 0,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Garmin GC 200 Manual

Product: