522218
17
Zoom out
Zoom in
Previous page
1/40
Next page
9
Testing the Installation
While it is possible to perform some checks with the boat trailered, the boat should be in the water to
properly test the sonar portion of the installation.
Press the POWER/BACKLIGHT key (see pg. 10) and the Fishfi nder 250/250C should power on. If the
unit fails to power on, verify that the wiring adapter is seated properly in the back of the unit, the Red and
Black wires are connected to the correct polarity, and that the 2-Amp fuse is installed and not blown. If the
unit is connected to a power supply that exceeds 35 volts DC, a “Battery Voltage High” warning is displayed
and the unit turns off. If the unit does not detect a transducer, it automatically enters Simulator Mode.
When the unit detects a transducer on initial power up, a “Please set up transducer” message is dis-
played. Press the ENTER key (see pg. 10) to select the transducer type. Highlight your transducer type with
the ARROW keys and press ENTER. Press ADJ/MENU to return to the Sonar display.
Since water is necessary to carry the sounder’s sonar signal, the transducer must be in the water to work
properly. It is not possible to get a depth/distance reading when out of the water. As the unit powers on, it
should immediately start showing the bottom. Verify that the unit is not in the simulator mode. If the unit
is in the simulator mode, make sure that the transducer is connected properly to the unit. When you place
your boat in the water CHECK FOR LEAKS around any screw holes that have been added below the water
line. DO NOT leave your boat in the water for an extended period of time without checking for leaks.
Begin testing the installation at a slow speed. If the sonar appears to be working properly, gradually
increase the boat’s speed while observing the sonar’s operation. If the sonar signal suddenly is lost or the
bottom return is severely degraded, note the speed at which this occurs. Return the boat to the speed the
signal was lost. Make moderate turns in both directions and see if the signal improves. If the signal strength
improves while turning, adjust the transducer so that it extends another 1/8" (3mm) below the transom of
the boat. It may take several adjustments to eliminate the degradation. If the signal does not improve, it may
be necessary to move the transducer to a different location.
NOTE: When adjusting the depth of the transducer, make the adjustments in small incre-
ments. Placing the transducer too deep can adversely affect the boat’s performance and put
the transducer at greater risk of striking underwater objects.
)
Installation
Testing the Installation
250C Manual.indd 9 1/27/2004, 3:55:01 PM
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Fishfinder 250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Fishfinder 250 in the language / languages: English as an attachment in your email.

The manual is 1,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info