GB
15
4. Technical data
Mains voltage: 230 V ~ 50Hz
Power input: 1200 W
Motor speed: 3,400 rpm
Cutting width: 32 cm
Cutting height adjustment: 25-60 mm; 3 levels
Volume of catch bag: 28 liters
L
pA
sound pressure level: 72 dB(A)
L
WA
sound power level: 96 dB(A)
Vibration at the handlebars: ≤ 2.5 m/s
2
Protection class: II / 쓑
5. Before starting the equipment
The lawn mower is delivered unassembled. The
complete push bar and the grass basket must be
assembled before using the lawn mower. Follow the
operating instructions step-by-step and use the
pictures provided as a visual guide to easily
assemble the machine.
Mounting the push bar (Fig. 3 to 10)
Take the push bar brackets and insert them into the
two respective openings (Fig. 3). Attach the push bar
brackets as shown in Fig. 4, using the screws
provided.
The lower push bar then has to be slid onto the push
bar bracket (Fig. 5). Important. Do not forget to first
insert the stress-relief clip (Fig. 5/Item A) onto the
lower push bar.
Screw the tubes together, using the screws supplied
(A), the plastic parts (B) and the hand wheel (C).
Now push the upper push bar over the lower push
bar (Fig. 7) and screw together as shown in Fig. 8.
Then attach the power cable to the push bar (Fig.
10/Item A) using the cable clips (Fig. 9/Item A).
Mounting the grass basket (Fig. 11 to 15)
Mount the bar frame as shown in Fig. 11. Pull the
grass bag over the bar frame (Fig. 12). The grass
bag must be fastened to the bar frame as shown in
Fig. 13 and 14. Before you fit the grass bag you must
ensure that the motor is switched off and the blade is
not rotating. Lift the ejector flap (Fig. 15 / Item A) with
one hand. With the other hand, hold the grass bag
by the handle and hook it in from above (Fig. 15).
Adjusting the cutting height
Important. Adjust the cutting height only when the
motor is switched off and the power cable has been
disconnected.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners are
damaged. To prevent any imbalance, replace blunt
and/or damaged blades. To carry out this check, first
switch off the motor and pull out the power plug.
The cutting height is adjusted as shown in Figs. 16
and 17. To do so, turn the equipment upside down or
tilt it to the side. Position both the front and rear axle
in the same notch, so that the cutting blade runs
parallel to the lawn.
Position A
Cutting depth: 60 mm
Position B
Cutting depth: 42.5 mm
Position C
Cutting depth: 25 mm
Power supply
The lawn mower can be connected to any light
socket-outlet with a 230 Volt alternating current.
However, the socket outlet must have an earthing
contact protected by a 16 A circuit breaker.
Additionally, a residual current device (RCD) circuit-
breaker with max. 30 mA must be used!
Power cable for the device
Please only use power cables that are not damaged.
The total length of the power cable should not
exceed 50 meters; going beyond this distance will
reduce the power output of the electric motor. The
power cable must have a cross-section of 3 x 1.5
mm
2
. The insulating sheath of lawn aerator power
cables is frequently damaged. Some of the causes
for this are:
Cuts caused by running over the cable
Pinching when the power cable is dragging
under doors and pulled through windows.
Cracking due to old age of the insulation
Kinking by improperly fastening or guiding the
power cable
The power cables must, at the very minimum, be of
type HO5RN-F and 3-stranded. The cable type must
be printed somewhere on the power cable. Only
purchase power cables that are marked as such!
Plugs and socket couplers for the power cables must
be made from rubber and be splash-proof. There is a
limit to how long power cables can be. Longer power
cables require larger conductor cross-sections.
Power cables and connecting lines must be regularly