724641
17
Zoom out
Zoom in
Previous page
1/21
Next page
45cc Petrol Chainsaw
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 53942 • 09/2018 • PM2006H
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
45cc Petrol Chainsaw
MODEL: №. 53942 • 09/2018 • PM2006H
30 31
Chain Sharpening
WARNING: Always ensure the engine is turned o before
undertaking this task.
Sharpen the chain regularly to maintain optimum performance of the
chainsaw.
Signs of a dull chain are:
The sawdust becomes powder-like
Extra force is required to execute a cut
The cut does not track in a straight line
Increased vibration
Increased fuel consumption
WARNING: Wear heavy gloves when handling the chain.
Hold the guide bar (19) securely in a vice.
Sharpen each cutter using a sharpening le (not supplied). Always use
outward strokes (Fig AL).
After sharpening, the cutters must all have the
same width and length. After every 3 - 4 times use
a repair centre to professionally sharpen your saw
chain. They have the special tools necessary to
ensure the correct cutting angles and depths
are even.
The suggested sharpening angle is 30 - 35°.
Guide Bar Wear
Reverse the guide bar (19) every 8 working hours
to ensure uniform wear. Check the bar rails fre-
quently and if necessary remove burrs and square-up the rails using a at
le.
AL.
NOTE: This product is not suitable for repair or maintenance work by the
unskilled person. The following detail explains how the product is cleaned, and
basic maintenance / safety checks.
All other maintenance work must be carried out by service agents who are
experienced with both the mechanical and electrical aspects of this product.
NOTE: Before cleaning your chainsaw or carrying out any maintenance
procedures, make sure that the engine is o and is cool.
NOTE: Failure to maintain the following parts may result in reduced engine
performance.
Disconnect the Spark plug to prevent accidental starting. Maintenance should
be performed before and after each use. If the chainsaw is dropped or appears
to suer any other signicant impact, it is highly recommended to perform all
maintenance tasks before operation, and if there appears to be an issue, refer
to the troubleshooting chart, or take to an authorised service agent.
Changing/replacing the Spark Plug
Regularly check the spark plug (17) for wear and
any build-up of carbon on the electrodes. Spark
plugs should be replaced every 10-15 hours of use.
1. Remove the air lter cover (15) by by rotating the
air lter cover knob in a anti - clockwise direction
until loose. Fully remove the knob and plastic
washer.
Lift the cover away from the saw housing (Fig AK).
WARNING: To avoid damage to the spark plug lead, ensure you hold
the rubber cap and not by the lead itself.
2. To remove spark plug (17) rst remove the rubber cap on the spark plug.
Then, using use the supplied combination tool (spark plug spanner) (33)
turn in an anti-clockwise direction to remove.
3. Check for oil on the electrodes and clean o any excess. This can typically
indicate that the fuel mixture ratio may be incorrect.
4. Use a soft wire brush to clean up carbon build up on spark plug electrodes.
Replace the spark plug or reset the electrode gap to 0.6-0.7mm.
Replacement spark plugs can be purchased from your local Lawnmower or
small engine store.
5. Reassemble in the reverse order.
Maintenance Chain sharpening
AK.
TIGHTEN
LOOSEN
Maintenance
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline PM2006H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline PM2006H in the language / languages: English as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info