724639
8
Zoom out
Zoom in
Previous page
1/16
Next page
26cc 2-Stroke Hedge Trimmer
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. MQE-3SPK-560 • 43671 • 09/2018
(toll free)
AFTER SALES SUPPORT
(toll free)
26cc 2-Stroke Hedge Trimmer
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. MQE-3SPK-560 • 43671 • 09/2018
12 13
14
11
Operation Operation
Starting A Cold Engine
CAUTION. Ensure the blade cover (22) is
removed before attempting to start the hedge
trimmer.
NOTE. Ensure the hedge trimmer has been
lled with the relevant fuel:oil 30:1 mixture
before proceeding with operation of the hedge
trimmer.
1. Place the hedge trimmer on a rm at surface.
2. Move the on/o Switch (10) to the “ON” position
on the on/o switch (10) (Fig A).
3. Your unit is designed with a 2 position choke:
Full Choke and
No Choke.
Move the red choke lever (18) to the Full Choke
position (Fig B).
4. Prime the carburettor by pressing the primer
bulb (17) 5-10 times or until there are no air
bubbles visible in the fuel discharge line. (Fig C).
5. Pull the recoil starter (8) out a short way until
resistance is felt (approximately pull: 4” / 10cm)
(Fig D). A smooth rapid pull is required for a
strong spark. Pull the recoil starter (8) briskly
4 times.
6. Once the engine starts allow to run for 10
seconds. At the same time press down the safety
lever (14) and the throttle trigger (11) and hold
in the full on position until the engine is running
smoothly (Fig E).
NOTE. If the engine starts at all and then stops,
even for 1 sec, move the choke lever (18) to the
mid way position between the full choke and no
choke position and pull the recoil starter (8)
to re start.
WARNING. On start up the oscillating
blades may be operational due to the
setting of the starting throttle.
Be well aware of this condition
7. Move the red choke lever (18) to the no choke position (Fig F) and allow
to run for a further 10 sec.
8. If the engine fails to start, repeat steps 1 through 7.
WARNING. On start up the oscillating blades may be operational
due to the setting of the starting throttle. Be well aware of this
condition.
NOTE. If the engine fails to start after repeated attempts, refer to
Troubleshooting section.
NOTE. Always pull the recoil starter (8) straight out. Pulling the recoil
starter (8) at an angle will cause it to rub against the eyelet. This friction
will cause the cord to fray and wear more quickly. Do not pull the end
of the cord, this can damage the recoil starter (8). Always hold the recoil
starter (8) handle when the cord retracts. Never allow the cord to snap
back from the extended position. This could cause the cord to snag or fray
and also damage the recoil starter (8) assembly.
A.
B.
C.
D.
E.
F.
Operation
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline MQE-3SPK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline MQE-3SPK in the language / languages: English as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info