724647
20
Zoom out
Zoom in
Previous page
1/26
Next page
31cc Brushcutter / Line Trimmer
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
(toll free)
AFTER SALES SUPPORT
(toll free)
31cc Brushcutter / Line Trimmer
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. BC35TS-2 • 08/2018 • 49290
36 37
WARNING: On start up, the output spindle may rotate under load when the
start trigger lock button (7) is used so ensure the cutting device is positioned
away from other persons, animals or debris. The start trigger lock button (7)
is for assistance in starting only and must not be used during operation. On
release of the throttle trigger (8), the motor must return to the idle speed and
the blade or line must NOT be turning under drive from the motor.
7. Once the engine is fully warm ensure the choke (red lever) (22) is down fully
to the run position (warm start).
Warm Start
When re starting the unit after it has been used and the motor is hot, there is
no need to engage the choke (red lever) (22) or the start trigger lock button
(7). Follow steps 4, 5, 6 & 7 on the previous page.
A Flooded Engine
If the choke (red lever) (22) has been left in the full choke position and the
engine will not start, it is possible the engine has been ooded
(Too much fuel).
To assist to clear a ooded engine:
1. Move the choke (red lever) (22) to the run or warm start position.
2. Squeeze the safety lever (9), and pull on fully the throttle trigger (8).
3. Check the on/o switch (10) is in the on position as indicated by an “I”.
4. Pull the recoil starter (2) a number of times to clear the fuel and start
the motor.
WARNING. Be aware that if starting occurs with the throttle pressed,
the motor will accelerate and thus engaging the clutch, which will then
rotate the cutting head.
As soon as the motor starts release the throttle so the motor runs at
idle speed and disengages the clutch.
Adjusting the speed on the Brushcutter / Line Trimmer
NOTE: The cutting head (spool and line) will not rotate at the idle speed.
The cutting head (spool and line) will engage and rotate when the speed of
the motor is increased.
1. To increase speed and engage the cutting head,
squeeze the safety lever (9) and then throttle
trigger (8) (Fig. BF).
2. To decrease the speed, slowly release the throttle
trigger (8) to the desired speed.
3. To disengage the cutter head (spool and line),
release all pressure on the throttle trigger (8)
and allow the motor to return to idle. The cutter
head (spool and line) will disengage at idle.
NOTE: Be aware that when using the 3T brushcutter blade (28), it will take a
few seconds to run down.
IMPORTANT: If the cutting head (spool and line) does not disengage and stop
when the throttle is in the idle position, TURN OFF the petrol motor and have
the unit checked at a service centre. This should be checked EVERY time the
motor is started.
Stopping the Brushcutter/ Line Trimmer
1. Release the throttle trigger (8) and allow the engine to idle for a
few moments.
2. Slide the on/o switch (10) to the ‘OFF’ position (towards to the lower
shaft) as marked with “STOP” and a directional arrow. Also indicated on
the side of the handle housing by an “O”.
3. The engine will now stop.
BF.
O
-
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline BC35TS-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline BC35TS-2 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info