711903

Gardena TCS Li-18-20 Art. 8866 Manual

8
Zoom out
Zoom in
Previous page
1/18
Next page
5. Operation
Working positions: The Pole Pruner can be operated in 2 working positions
(above/below). To ensure a tidy cutting edge, thick branches
should be cut in 2 steps (Illustrations similar).
max. 4m
max. 4 m
max. 4 m
A
ß
ß
B
Above
(thick branches):
1. From below, saw the
branch to no more
than 1/3 of the dia meter
(chain will push towards
the stop at
the front ß
A
).
Above
(thick branches):
2. Cut off the branch
from above (chain
will push towards the
stop at the back ß
B
).
Below:
Cut off from above
(chain will push towards
the stop at the back ß
B
).
DANGER!
Do not stand under the branch while cutting.
Tilting the motor unit:
0°
15°
30°
45°
60°
-15°
-30°
-45°
-60°
0
1
The motor unit 1 can be tilted in 15° increments from
60° to – 60°.
1. Remove the battery from the handle (see 4. Initial Operation).
2. Keep both orange buttons 0 pressed.
3. Tilt motor unit 1 in the required direction.
4. Release both orange buttons 0 and allow motor unit 1 to
engage.
5. Put the battery on the handle (see 4. Initial Operation).
Extending the telescopic
pipe:
50 cm
q
2
The telescopic tube 2 can be continuously extended by up to
50 cm.
1. Remove the battery from the handle (see 4. Initial Operation).
2. Loosen the orange nut q, extend the telescopic pipe 2 to the
require length, and tighten the orange nut q again.
3. Put the battery on the handle (see 4. Initial Operation).
22
GB
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena TCS Li-18-20 Art. 8866 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena TCS Li-18-20 Art. 8866 in the language / languages: English as an attachment in your email.

The manual is 6.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gardena TCS Li-18-20 Art. 8866

Gardena TCS Li-18-20 Art. 8866 User Manual - German - 11 pages

Gardena TCS Li-18-20 Art. 8866 User Manual - Dutch - 19 pages

Gardena TCS Li-18-20 Art. 8866 User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info