687471
44
Zoom out
Zoom in
Previous page
1/56
Next page
Message Cause Action
Outside working area
The boundary wire connections to the charg-
ing station are crossed.
Check that the boundary wire is connected
correctly.
The boundary wire is too close to the edge of
the working area.
Check that the boundary wire has been laid
according to the instructions. See
Installation
on page 26
.
The working area slopes too much by the
boundary loop.
The boundary wire is laid in the wrong direc-
tion around an island.
Disturbances from metal objects (fences, re-
inforcement steel) or buried cables close by.
Try moving the boundary wire.
The robotic lawnmower finds it hard to distin-
guish the signal from another robotic lawn-
mower installation close by.
Place the robotic lawnmower in the charging
station and generate a new loop signal, see
New loop signal on page 26
.
Empty battery
The robotic lawnmower cannot find the charg-
ing station.
Check that the charging station and the guide
wire are installed in accordance with the in-
structions. See
Installation of the guide wire
on page 18
.
The guide wire is broken or not connected. Find out where the break is and rectify it.
The battery is spent. Replace the battery. See
Battery on page 41
.
The charging station’s antenna is defective. Check if the indicator lamp in the charging
station flashes red. See
Indicator lamp in the
charging station on page 47
.
Wrong PIN code
Wrong PIN code has been entered. Five at-
tempts are permitted, and the keypad is then
blocked for five minutes.
Enter the correct PIN code. Contact your lo-
cal GARDENA representative if you forget the
PIN code.
No drive
The robotic lawnmower has got caught in
something.
Free the robotic lawnmower and rectify the
reason for the lack of drive. If it is due to wet
grass, wait until the lawn has dried before us-
ing the robotic lawnmower.
The working area includes a steep slope. Maximum guaranteed slope is 40%. Steeper
slopes should be isolated. See
Slopes on
page 16
.
The guide wire is not laid at an angle on a
slope.
If the guide wire is laid on a slope, it must be
laid at an angle across the slope. See
Instal-
lation of the guide wire on page 18
.
Wheel motor overloa-
ded, right
The robotic lawnmower has got caught in
something.
Free the robotic lawnmower and rectify the
reason for the lack of drive. If it is due to wet
grass, wait until the lawn has dried before us-
ing the robotic lawnmower.
Wheel motor overloa-
ded, left
Charging station
blocked
The contact between the charging strips and
contact strips may be poor and the robotic
lawnmower has made a number of attempts
to charge.
Put the robotic lawnmower in the charging
station and check that the charging strips and
contact strips make good contact.
An object is obstructing the robotic lawnmow-
er.
Remove the object.
The charging station is tilted or bent. Confirm that the charging station is placed on
a fully flat and horizontal ground. The charg-
ing station must not be tilted or bent.
44 - Troubleshooting 307 - 002 - 11.10.2017
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena Smart SILENO R100LiC - 2018 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena Smart SILENO R100LiC - 2018 in the language / languages: English as an attachment in your email.

The manual is 7,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gardena Smart SILENO R100LiC - 2018

Gardena Smart SILENO R100LiC - 2018 User Manual - German - 64 pages

Gardena Smart SILENO R100LiC - 2018 User Manual - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info