687473
17
Zoom out
Zoom in
Previous page
1/56
Next page
100 cm / 40"
100 cm / 40"
100 cm / 40"
20 cm / 8"
0-15 cm / 0-6"
0-40 cm / 0-16"
15- cm / 6-"
0-40%
3.5.4 Laying the boundary wire
If you intend to staple down the boundary wire:
Cut the grass very low with a standard lawnmower
or a trimmer where the wire is to be laid. It will then
be easier to lay the wire close to the ground and the
risk of the robotic lawnmower cutting the wire or
damaging the insulation of the wire is reduced.
Make sure to lay the boundary wire close to the
ground and secure the pegs close together. The
cable must lie close to the ground so as not to be cut
before the grass roots have grown over it. Mowing
the grass too low right after the installation can
damage the wire insulation. Damage to the
insulation may not cause disruptions until several
weeks or months later. To avoid this, always select
the maximum cutting height the first weeks after
installation and then lower the height one step at a
time every second week until the desired cutting
height has been reached.
Use a hammer to knock the pegs into the ground.
Exercise care when knocking the pegs and make
sure the wire is not under strain. Avoid sharp bends.
If the boundary wire is to be buried:
Make sure to lay the boundary wire at a minimum of
1 cm and a maximum of 20 cm in the ground. The
wire can be buried for instance using an edge cutter
or a straight spade.
Note: Extra wire must not be placed in coils outside the
boundary wire. This can disrupt the robotic lawnmower.
3.5.4.1 Eyelet for connecting the guide wire
To facilitate the connection of the guide wire to the
boundary wire, it is recommended to create an eyelet
with about 20 cm of extra boundary wire at the point
where the guide wire will later be connected. It is a good
idea to plan where the guide wire will be placed before
laying out the boundary wire. See
Laying the boundary
wire on page 17
.
3.5.4.2 Laying the boundary wire in towards the
charging station
On its way toward the charging station, the boundary
wire can be laid completely outside the charging station
(see option 1 in the figure). If there is a need to partly
locate the charging station outside the working area, it is
also possible to lay the wire under the charging station
plate (see option 2 in the figure).
However most of the charging station must not be
placed outside the working area as the robotic
lawnmower can then find it difficult to find the charging
station (see figure).
307 - 002 - 11.10.2017 Installation - 17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena SILENO plus R160Li -2018 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena SILENO plus R160Li -2018 in the language / languages: English as an attachment in your email.

The manual is 7,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gardena SILENO plus R160Li -2018

Gardena SILENO plus R160Li -2018 User Manual - German - 64 pages

Gardena SILENO plus R160Li -2018 User Manual - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info