584652
2
Zoom out
Zoom in
Previous page
1/2
Next page
1. Main switch
2. STOP button
3. LED for function check of the
boundary and guide wires
4. Cutting height indication
5. Display
6. Keypad
1. Placement of and connecting the charging
station
See chapter 3.2 in the Operator’s Manual
1. Place the charging station at a central position in the work area, with a lot of open
space in front of the charging station and on a relatively horizontal surface.
2. Connect the transformer’s low voltage cable to the charging station and the
transformer.
3. Connect the transformer to a 230 V wall socket.
2. Charging the battery and
placement of the boundary wire
See chapter 3.3 and 3.4 in the Operator’s Manual
1. Place the robotic lawnmower in the charging station to charge
the battery while the boundary wire is laid. Set the main
switch to position 1.
2. Run the boundary wire ensuring it forms a loop around the
wor
k area.
3. Make an eyelet at the point where the guide wire will be
connected later (see point 4.5).
Charging station
12345
1 2 3
4 5 6
7 8
0
9
GARDENA
Start
4
5
6
1
2
3
1
2
3
20 cm / 8
10 cm / 8”
0 cm / 0”
5 cm / 2”
30 cm / 12”
GETTING STARTED WITH
THE GARDENA ROBOTIC LAWNMOWER
3. Connecting the boundary wire
See chapter 3.5 in the Operator’s Manual
1. Open the connector and lay the wire ends in the recesses on each connector.
2.
Press the connectors together using a pair of pliers.
3. Cut off any surplus boundary wire. Cut 1 to 2 cm above the connectors.
4. Press the connectors onto the contact pins, marked A, on the charging station. It is
important that the right-hand wire is connected to the right-hand contact pin, and the
left-hand wire to the left-hand pin.
4. Placement of and connecting the guide
wire
See chapter 3.6 in the Operator’s Manual
1. Run the guide wire through the slot at the bottom of the charging station.
2.
Fit the connector to the guide wire in the same way as for the boundary wire,
according to the instructions above.
3. Fasten the connector to the contact pin marked Guide on the charging station.
4. Lay the guide wire at least 2 metres straight out from the front edge of the
charging station.
5. Run the guide wire to the point on the boundary loop the connection will be made.
Avoid laying the wire at tight angles.
6. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made
in point 2.3.
7. Connect the guide wire to the boundary wire using the accompanying couplers.
Press the couplers completely together with a pair of pliers.
Transformer Low voltage cable Boundary wire and
couplers
Staples Connectors Measurement
gauge
1
7
4
2
4
3
min 2 m / 7 ft
1
1
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena R40Li Robot at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena R40Li Robot in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gardena R40Li Robot

Gardena R40Li Robot User Manual - English - 76 pages

Gardena R40Li Robot Quick start guide - German - 2 pages

Gardena R40Li Robot User Manual - German - 80 pages

Gardena R40Li Robot Additional guide - Dutch - 5 pages

Gardena R40Li Robot Quick start guide - Dutch - 2 pages

Gardena R40Li Robot User Manual - Dutch - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info