672938
73
Zoom out
Zoom in
Previous page
1/84
Next page
English - 72
TROUBLESHOOTING
Connectivity settings
restored
The connectivity settings was
restored due to a fault.
Please check and change the settings if
needed.
Poor signal quality
The connectivity circuit board in the
mower is assembled upside down,
or the mower itself is tilted or upside
down.
Verify the mower is not upside down or
tilted. If not, the message requires action by
authorized service technician.
9.2 Info messages
A number of info messages are listed below that can be shown on the display on the robotic lawnmower. It is
recommended to contact GARDENA Central Service if the same message appears often. Check that the installation is
performed as described in the Operator’s Manual. Contact GARDENA Central Service .
Message Cause Action
Low battery
The robotic lawnmower cannot nd
the charging station.
Check that the charging station and the guide wire
are installed in accordance with the instructions.
See 3 Installation on page 15.
The guide wire is broken or not
connected.
Find out where the break is and rectify it.
The battery is spent.
Replace the battery. See Replacing battery on
page 68
The charging station’s antenna is
defective.
Check if the indicator lamp in the charging station
ashes red. See 9.3 Indicator lamp in the charging
station on page 73.
Settings restored
Conrmation that a Reset all user
settings has been carried out.
This is normal. No action required.
Guide not found
The guide wire is not connected to
the charging station.
Check that the guide wire’s connector is tightly
connected to the charging station. See 3.6
Installation of the guide wire on page 28.
Break in the guide wire.
Find out where the break is. Replace the
damaged section of the guide wire with a new
loop wire and splice using an original coupler.
The guide wire is not connected to
the boundary loop.
Check that the guide wire is connected correctly
to the boundary loop. See 3.6 Installation of the
guide wire on page 28. Splice using an original
coupler.
Guide calibration
failed
The robotic lawnmower has failed to
calibrate the guide wire.
Check that the guide wires are installed according
to the instructions, See 3.6 Installation of the
guide wire on page 28
Guide calibration
accomplished
The robotic lawnmower has
succeeded to calibrate the guide wire.
No action required.
Difcult nding home
The robotic lawnmower has been
following the boundary wire several
laps without nding the charging
station.
The installation has not been done correctly.
See Laying the boundary wire on page 25.
Wrong corridor width setting on boundary wire.
See Finding the charging station on page 13.
The mower was started on a Secondary area with
the Main area setting.
1157808,Gardena_R100Li-R130Li,GB_151217.indd 72 2016-01-12 09:17:10
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena R100LiC Sileno at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena R100LiC Sileno in the language / languages: English as an attachment in your email.

The manual is 14,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gardena R100LiC Sileno

Gardena R100LiC Sileno Quick start guide - German - 4 pages

Gardena R100LiC Sileno User Manual - German - 64 pages

Gardena R100LiC Sileno User Manual - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info