584683

Gardena EasyCut Li-18-23 - 9824 Manual

10
Zoom out
Zoom in
Previous page
1/17
Next page
Releasing a cutting filament
that has gone into the
cassette or which has fused:
Y
X
U
z
37
If the cutting filament has disappeared into the filament cassette
or if the automatic filament extension still doesn’t work after
pulling the cutting filament
U
it may be fused together in the
filament cassette
Y
.
1. Remove the battery.
2. Remove the filament cassette
Y
as described in
7. Maintenance “Replacing the filament cassette”.
3. Unwind the cutting filament
U
, clean the filament cassette
Y
and the cutting filament
U
and wind the cutting filament
U
onto
the cassette
Y
once more.
4. Clean the automatic mechanism lever
ß
37
.
The automatic lever must move freely.
5. Insert the filament cassette again as described under
7. Maintenance “Replacing the filament cassette”.
Problem Possible Cause Remedy
The trimmer no longer cuts Filament cassette empty.
v Replace the filament cas sette
(see 7. Maintenance
“Replac ing the filament
cassette” ).
Cutting filament too short or the
automatic filament extension
does not work.
v Pull the filament out of the
cassette manually.
Cutting filament inside the
cassette or fused.
v Release filament that has
disappeared into the cassette
or fused together.
The filament cannot be
extended
The filament became too dry and
brittle (e. g. over the winter).
v Place the filament cassette in
lukewarm water for approx.
10 hours.
The trimmer does not start Battery is flat.
v Charge battery
(see 4. Initial Operation).
Battery not pushed onto the
handle properly.
v Push battery onto the handle
and make sure that the locking
buttons snaps in correctly.
Motor blockage.
v Unblock and restart the
device.
The filament consumes
quickly
Frequent contact between the
filament and hard objects.
v Avoid contact between the
filament and hard objects.
The trimmer stops.
Error-LED
ß
W
flashes
Battery overload.
v Wait for 10 sec. Press button
ß
B
on the battery and restart.
High temperature. The allowed
operation temperature was
exceded.
v Leave battery to cool for
approx. 15 min. Press button
ß
B
on the battery and restart.
Charging indicator lamp
9
on
the charger does not light up
Battery charger or charging
cable not plugged in properly.
v Plug in battery charger and
charging cable properly.
Charging control lamp
9
on the charger flashes rapidly
(twice per second)
Charging error.
v Unplug charger and plug
in again.
21
GB
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena EasyCut Li-18-23 - 9824 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena EasyCut Li-18-23 - 9824 in the language / languages: English as an attachment in your email.

The manual is 2,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gardena EasyCut Li-18-23 - 9824

Gardena EasyCut Li-18-23 - 9824 User Manual - German - 17 pages

Gardena EasyCut Li-18-23 - 9824 User Manual - Dutch - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info