672921

Gardena 19030 smart Sensor Manual

11
Zoom out
Zoom in
Previous page
1/34
Next page
756
ß
P
1. Push the flap
5
and open the lid
6
.
2. Remove the battery holder
7
.
3. Insert the batteries into the battery holder
7
.
When doing so, ensure correct polarity
ß
P
.
4. Insert battery holder
7
in the sensor.
5. Close the lid
6
.
To select correct location
for Sensor:
Correct location:
The Sensor must be positioned at a location in the watering area
which is exposed to the same climatic conditions as the plants
(sun, wind, rain, etc.) for which a status is to be displayed.
Incorrect location:
The Sensor should not be covered by neighbouring plants.
Areas of shade should be avoided.
To rule out erroneous reaction results caused by waterlogging,
the Sensor should not be positioned in dips in the ground.
The sensor should not be positioned in places, where lawnmowers
mow.
To “plant” the Sensor :
4
0
8
WARNING!
The tip of the sensor will only measure the soil mois-
ture correctly if the sensor tip is in full contact with
the ground on all sides! No air should be trapped at
the sensor tip in the ground.
1. Dig a funnel-shaped hole in the ground
8
at least 12 cm deep.
2. Break up the soil
8
removed and take out any stones.
3. If the soil is dry, moisten.
4. Replace the damp broken-up soil
8
in the funnel-shaped hole
without packing tight.
5. Immerse entire sensor tip
4
in water (felt must be wet).
6. Insert the Sensor to the upper edge of the sensor
0
in the
broken-up soil
8
.
Here the sensor tip
4
must be in full contact with the damp soil
on all sides.
7. Press down the soil
8
around the sensor
0
lightly.
The Sensor should not stand loose in the ground.
8. Water the area around the Sensor with approx. 1 litre water.
Depending on the ground it may take several hours until the
Sensor measures the actual soil moisture.
HINT: To Connect GARDENA Micro-Drip-System:
To ensure that the quantity of water delivered is registered by the
sensor tip when using the GARDENA Micro-Drip-System, a drip
head should be installed directly above the sensor.
11
GB
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena 19030 smart Sensor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena 19030 smart Sensor in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info