22881

Gaggia Syncrony Compact Digital Manual

18
Zoom out
Zoom in
Previous page
1/67
Next page
ENGLISHENGLISH
• 35 •• 34 •
10Turn the steam knob (16) anticlockwise to
empty out the contents of the water tank
MACHINE IS RINSING
11When the machine rinse cycle is completed
the display will show:
RINSING FINISHED
CLOSE KNOB
12Close the tap, reload the circuit and let the
machine heat up
If you use a product other than the
recommended one, you should
follow the manufacturer’s directions on
the package.
11.1 Interrupting the descaling cycle
If the descaling cycle is interrupted
by switching the machine OFF, it will
automatically resume when the machine is
switched back ON.
The descaling cycle can be interrupted by turning
the steam knob (16) clockwise and then pressing
the button (27).
The display will show:
DESCAL. INTERRUPTED
EMPTY WATERTANK
Warning! After interrupting the cycle
you must empty the water tank of the
descaling solution and wash out the tank
with fresh drinking water; the machine
circuit must be cleansed by carrying out a
rinse cycle. The display will show:
RINSE MACHINE
PRESS KEY
Follow the directions for a normal rinse cycle
provided in section 8 of the previous chapter.
12 FUNCTION PROGRAMMING
The user can change some machine
operating parameters according to
personal needs.
12.1 MENU/OK command
In order to program functions you must access
the programming mode by pressing “MENU/
OK” (28) when the machine is in a standby status.
To select the desired function, press the “∧”
button to move up one line or the “∨” button to
move down on the display.
To exit the programming mode press “ESC”
12.2 Choosing individual functions
Select the desired function by pressing “∧” or
“∨”. Press “MENU/OK” to enable the desired
function; you can browse the selectable settings
using the “∧” or “Ú” button; to store a setting
press “MENU/OK”.
Note: by pressing “ESC” you can exit
the programming mode at any time
without saving the changes made; exiting
without saving is possible only before you
have pressed “MENU/OK”.
12.3 Description of programmable
functions
ENERGY SAVING
If the appliance is used little, it may be switched to
the ENERGY SAVING mode. This function allows
electricity costs to be reduced. However, it is
recommended to switch the appliance off completely
using the on/off switch (7) if it is not to be used for a
prolonged period. It will take the machine just a few
minutes to heat up when you switch it back on.
• In the programming mode press “∧” or “∨”
to select the function:
ENERGY SAVING
and enable it by pressing “MENU/OK”; the
following message will appear:
ENERGY SAVING
in this mode the machine remains on but no
components are active.
•To deactivate the “ENERGY SAVING”
function, press “MENU/OK”.
RINSING
Immediately after heating up, the appliance
automatically eliminates the water left standing
in the internal circuit to ensure that only fresh
water will be used to make coffee.
The function is activated in the factory.
• To deactivate it, go to the programming mode
and press “∧” or “∨” to select the function:
RINSING
and enable it by pressing “MENU/OK”. The
following message will appear:
RINSING
ON
Now press “∧” or “∨”to select
RINSING
ON
RINSING
OFF
and store the selection by pressing “MENU/OK”.
We recommend selecting:
RINSING
ON
LANGUAGE
This function allows you to change the
language of the display. You can choose
among Italian, German, Portuguese, Spanish,
English, French and Dutch. The appliance is
normally set on the language of the country it
is to be sold in.
• After accessing the programming mode, press
“∧” or “∨” to select the function:
LANGUAGE
and then enable it by pressing “MENU/OK”.
The display will show:
LANGUAGE
ENGLISH
Press “∧” or “∨” to select the desired language
and then press “MENU/OK” to memorise it.
WATER HARDNESS
The hardness of tap water may vary from
region to region. For this reason, the
appliance may be adjusted according to the
degree of hardness of the water in the place
it will be used in; hardness is measured on a
scale of 1 to 4.
The appliance is already programmed for
an average value (hardness 3). The
appliance setting should be adjusted according
to the actual hardness of the water, which can
be measured using the test strip provided.
Briefly dip (1 second) the test strip
provided in water and shake it gently. After
one minute you can read the test results
on the strip.
• After accessing the programming mode press
“∧” or “∨” to select the function:
WATER HARDNESS
and enable it by pressing “MENU/OK”.
• The display will show:
WATER HARDNESS
HARDN 3
• Check the test strip previously immersed in
water to see how many squares have changed
colour.
• Press “∧” or “∨” to select the correct water
hardness (e.g. 2 squares = Hardness 2) and
memorise it by pressing “MENU/OK”.
Caution: descale the appliance when
the max water hardness level is reached.
The display will show the message:
DESCALING
READY FOR USE
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggia Syncrony Compact Digital at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggia Syncrony Compact Digital in the language / languages: Dutch as an attachment in your email.

The manual is 3,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info