702925
25
Zoom out
Zoom in
Previous page
1/28
Next page
25
FAQ
en
What to do in the event of a fault
Usually, faults are small matters that are easy to
eliminate. Please read the information in the table
before calling the after-sales service.
Notes
If the fault code is not listed in the table, disconnect
the hob from the mains power supply and wait
30 seconds before reconnecting it. If this code is
displayed again, contact the technical after-sales
service and specify which fault code has appeared.
If a fault occurs, the appliance will not switch to
standby mode.
Indicator/symbol Possible cause Remedial action
None The power supply has been disconnected. Use other electrical appliances to check whether a
short circuit has occurred in the power supply.
The appliance has not been connected as
shown in the circuit diagram.
Check that the appliance has been connected as
shown in the circuit diagram.
Electronic fault. If the fault cannot be rectified, inform the technical after-
sales service.
An audible signal will
sound.
The control panel is wet or an object is cov-
ering it.
Dry the control panel or remove the object.
The hotplate has been
switched off. The illumi-
nated ring on the control
knob is flashing.
The control knob has not been turned for
an extended period. The automatic safety
switch-off function has been activated.
Turn the control knob to position 0. Switch the hotplate
back on.
The appliance is too hot. Read the fault message on the control panel.
The hotplate indicator is
flashing.
The cookware is not being detected. Make
sure that the cookware is suitable for use
with an induction hob.
Make sure that the diameter of the base of the cook-
ware corresponds to the size of the hotplate. Turn the
control knob to position 0. Switch the hotplate back on.
”ƒ
The electronics have overheated and have
switched off the corresponding hotplate.
Remove any cookware from the hob. Once the fault
code goes out, the hotplate has cooled down suffi-
ciently. Turn the control knob to position 0. Then select
the heat setting as usual.
”…
The electronics have overheated and all
the hotplates have been switched off.
Ӡ + heat setting and sig-
nal tone
There is hot cookware on/near the control
panel. There is a risk that the electronics
will overheat.
Remove the cookware.The fault code will go out shortly
afterwards. You can resume cooking.
Ӡ and signal tone
There is hot cookware on/near the control
panel. To protect the electronics, the hot-
plate has been switched off.
Remove the cookware. Wait a few seconds. When the
fault code on the display goes out, you can resume
cooking.
”‚ / ”‡
The hotplate has overheated and has been
switched off to protect the work surface.
Wait until the electronics have cooled down sufficiently
before switching the hotplate on again.
”‰
The hotplate has been operating continu-
ously for an extended period.
The automatic safety switch-off function has been acti-
vated. See the section entitled ~ "Automatic safety
switch-off function"
”Š
The FlexPlus cooking zone will not activate. Touch any touch control to check the fault code. You
can use the remaining hotplates to cook as usual. Con-
tact the technical after-sales service.
“Š‹‹‹
“Š‹‚‹
The operating voltage is incorrect/outside
of the normal operating range.
Contact your electricity supplier.
—…‹‹
The hob is not connected properly. Disconnect the hob from the power supply. Check that
it has been connected as shown in the circuit diagram.
Do not place hot cookware on the control panel.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggenau VI482111 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggenau VI482111 in the language / languages: English as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gaggenau VI482111

Gaggenau VI482111 User Manual - German - 28 pages

Gaggenau VI482111 User Manual - Dutch - 56 pages

Gaggenau VI482111 User Manual - French - 28 pages

Gaggenau VI482111 User Manual - Italian - 56 pages

Gaggenau VI482111 Installation Guide - All languages - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info