760883
33
Zoom out
Zoom in
Previous page
1/36
Next page
32
en Trouble shooting
3
Trouble shooting
Trouble shooti ng
Usually, faults are small matters that are easy to
eliminate. Please read the information in the table
before calling the after-sales service.
Notes
If the fault code is not listed in the table, disconnect
the hob from the mains power supply and wait
30 seconds before reconnecting it. If this code is
displayed again, contact the technical after-sales
service and specify which fault code has appeared.
If a fault occurs, the appliance will not switch to
standby mode.
Display Possible cause Solution
None The power supply has been disconnected. Use other electrical appliances to check whether a
short circuit has occurred in the power supply.
The appliance has not been connected as
shown in the circuit diagram.
Make sure that the appliance has been connected as
shown in the circuit diagram.
Electronics fault. If the fault cannot be rectified, inform the technical after-
sales service.
A signal sounds. The control panel is wet or an object is cov-
ering it.
Dry the control panel or remove the object.
The hotplate has been
switched off. The illumi-
nated ring on the control
knob is flashing.
The control knob has not been turned for
an extended period. The automatic safety
cut-out function has been activated.
Turn the control knob to position 0. Switch the hotplate
back on.
The appliance is too hot. Read the fault message on the control panel.
The hotplate indicator is
flashing.
The cookware is not being detected. Make
sure that the cookware is suitable for use
with an induction hob.
Make sure that the diameter of the base of the cook-
ware corresponds to the size of the hotplate. Turn the
control knob to position 0. Switch the hotplate back on.
”ƒ The electronics have overheated and have
switched off the affected hotplate.
Remove any cookware from the hotplate. Once the fault
code goes out, the hotplate has cooled down suffi-
ciently. Turn the control knob to position 0. Then select
the heat setting as usual.
”… The electronics have overheated and all of
the cooking zones have been switched off.
Ӡ + heat setting and sig-
nal tone
There is hot cookware near the control
panel. There is a risk that the electronics
will overheat.
Remove the cookware. The fault code goes out shortly
afterwards. You can resume cooking.
Ӡ and signal tone There is hot cookware near the control
panel. The cooking zone has been
switched off to protect the electronics.
Remove the cookware. Wait a few seconds. When the
fault code on the display goes out, you can resume
cooking.
”‚ / ”‡ The hotplate has overheated and has been
switched off to protect the work surface.
Wait until the electronics have cooled down sufficiently
before switching the hotplate on again.
”‰ The hotplate has been operating continu-
ously for an extended period.
The automatic safety cut-out function has been acti-
vated. See section ~ "Automatic safety switch-off
function".
”Š The FlexPlus cooking zone cannot be acti-
vated.
Touch any touch control to check the fault code. You
can use the remaining cooking zones to cook as usual.
Contact our technical after-sales service.
“Š‹‹‹
“Š‹‚‹
The operating voltage is incorrect/outside
of the normal operating range.
Contact your electricity supplier.
—…‹‹ The hob is not connected correctly. Disconnect the hob from the mains. Make sure that it
has been connected as shown in the circuit diagram.
Do not place hot cookware on the control panel.
33
Customer service en
Demo mode
If š“ ‹¯ is displayed, demo mode has been activated.
The appliance will not heat up. Disconnect the
appliance from the power supply. Wait 30 seconds
before reconnecting it. Then deactivate demo mode
within 3minutes as follows:
1Turn one of the control knobs anti-clockwise to
position Ž.
2Turn the same control knob clockwise to position 1.
3Turn the same control knob anti-clockwise to
position 0.
The illuminated ring around the control knob will be
lit yellow.
4Turn the same control knob clockwise to position 1.
‹¯ will be lit and the illuminated ring will be green.
Wait 5seconds. ‹”” will be lit and the illuminated
ring will turn yellow.
Demo mode has now been deactivated.
4
Customer service
Customer service
Our after-sales service is there for you if your appliance
needs to be repaired. We will always find an appropriate
solution, also in order to avoid after-sales personnel
having to make unnecessary visits.
E number and FD number
When calling us, please quote the full product number
(E no.) and the production number (FD no.) so that we
can provide you with the correct advice. The rating plate
that features these numbers can be found on the
underside of the appliance.
The product number (E no.) can also be found on the
glass-ceramic hob. You can check the after-sales
service index (KI) and production number (FD no.) by
going to the basic settings. Refer to the section entitled
~ "Basic settings" to find out how to do this.
To save time, you can make a note of the numbers for
your appliance and the telephone number of the after-
sales service in the space below in case you need them.
Please note that a visit from an after-sales service
engineer is not free of charge in the event that the
appliance has been misused, even during the warranty
period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
Trust the expertise of the manufacturer, and rest
assured that the repair will be carried out by trained
service technicians using original spare parts for your
domestic appliance.
E no. FD no.
After-sales service O
GB 03448928988
Calls charged at local or mobile rate.
IE 014502655
0.03€ per minute at peak.
Off peak 0.0088€ per minute.
AU 1300368339
NZ 094770492
=1U)'(1U
7\SH
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggenau VI462113 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggenau VI462113 in the language / languages: English as an attachment in your email.

The manual is 2,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gaggenau VI462113

Gaggenau VI462113 User Manual - German - 36 pages

Gaggenau VI462113 User Manual - Dutch - 36 pages

Gaggenau VI462113 User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info