123576
13
Zoom out
Zoom in
Previous page
1/23
Next page
13
Washing dishes
Reduce costs!
If only a small number of dishes have been loaded into
the dishwasher, selecting a programme that operates
at the next lowest temperature will usually suffice.
Programme data
The programme specifications can be found in the
summary of instructions. Programme specifications
refer to normal conditions. Greater deviations may
occur due to:
different amounts of dishes
temperature of mains water supply
pressure of mains water supply
ambient temperature
fluctuations in mains voltage
machine-related factors (e.g. temperature, water
volume, ...).
Energy and water consumption is reduced by up to 1/4
when dishes are washed in the upper basket only.
Water consumption values are based on a water
hardness setting of 4.
Aqua sensor *
* some models
The Aquasensor is an optical measuring device (light
barrier) which measures the turbidity of the rinsing
water.
The Aqua sensor is used according to the programme.
When the Aqua sensor is active, “clean” rinsing water
may be transferred into the next rinsing bath and/or the
temperature adjusted. If the turbidity is greater, the
water is drained and is replaced with fresh water. In this
way water consumption can be reduced
by approx. 4 litres.
Switching the dishwasher ON
Turn on the tap.
Set main switch
1
to ON.
Indicators light up according to the last programme
that was selected.
This same programme will run again if no other
programme button
6
is
pressed
The numerical display
8
shows the expected
duration of the programme.
Close door.
The programme starts automatically.
Programme sequence indicator
9
Your dishes are being cleaned.
Your dishes are being dried.
Your dishes are being rinsed.
Optical indicator during operation *
* With some models
During the rinse programme a light point appears on
the floor below the device’s door. Only open the
dishwasher door when the light point has disappeared.
In the case of built-in dishwashers with flush front the
light point will not be visible.
Remaining running time display
When the appliance has started, the expected
programme running time is displayed. The programmed
running time is affected by the water temperature, the
number of dishes, as well as the degree of soiling. If
these conditions are changed, the running time
(depending on the selected programme) can vary
greatly. As the effect is not detected until a programme
is running, the time may be longer or shorter than
expected.
Time delay *
* on applicable models
You can delay the start of the programme in 1-hour
steps up to 19 hours.
Switch on the appliance.
Press the timer programming button
3
until the
digital display
8
jumps to .
Keep pressing the timer programming button until
the required time is displayed.
To delete the timer programming, keep pressing the
button until
is displayed.
You can change your programme selection at any
time until the programme starts.
End of programme
The end of the programme is indicated by a buzzer.
This function can be changed as follows:–
Hold down Function button C pressed and switch
on main switch
1
, then let the buttons go.
Function Button
C flashes, and the digital display
indicates the value
which was set at the factory
(semi-loud).
To change the setting:
Press Function button
C .
Each depression of the button increases the set
value by one, when is reached, the display
jumps back to
(off).
Switch off the main switch
1
.
The set value is stored in the appliance.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggenau di 460-110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggenau di 460-110 in the language / languages: English as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gaggenau di 460-110

Gaggenau di 460-110 User Manual - German - 23 pages

Gaggenau di 460-110 User Manual - Dutch - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info