761927
47
Zoom out
Zoom in
Previous page
1/56
Next page
46
en Hood control
Connecting appliances via your home network
If the appliances are connected to each other via your
home network, both the hood controls and Home
Connect can be used to operate the hob.
Notes
Make sure you follow the safety instructions in the
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the
hob.~ "Important safety information" on page 5
If the appliance is being operated by means of the
controls on the extractor hood, this mode of
operation always has priority. It is not possible to
use the hood controls on the hob during this time.
In networked standby mode, your appliance
requires a maximum of 2 W.
Setting up
To set up the connection between the hob and cooker
hood, the hob must be switched on.
Connecting directly
Make sure that the extractor hood is switched off.
For more information refer to the section entitled
"Connecting to the hob" in the instruction manual for
your extractor hood.
Note: If you connect your hob directly to the extractor
hood, it cannot be connected to your home network as
well and you will not be able to use Home Connect.
1To open the basic settings, touch the t symbol on
the main screen.
2Scroll left or right with your finger and select the
Hood control setting }.
3Select the Hood control option and then touch the
G symbol to confirm your choice.
4You have 2 minutes to initiate the connection
process on the extractor hood. See extractor hood
operating instructions.
Once the process is complete, a message will be
displayed, informing you of the result of the connection
process. If the connection has been successfully
established, the S symbol for ventilation control from
the hob will appear on the main screen.
If you wish to change the setting, select the Hood
control option S again and then change the setting as
required.
Connecting via your home network
You require a router that has WPS functionality.
Access to your router is required. If you do not have this,
follow the steps listed under "Direct connection".
When you begin, make sure that the extractor hood is
connected to the same home network.
1To open the basic settings, touch the t symbol on
the main screen.
2Scroll left or right with your finger and select the
Hood control setting }.
3Select the Home network option and then touch
the G symbol to confirm your choice.
4Press the WPS button on the router within the next
2 minutes.
A message will be displayed to notify you when the
hob is successfully connected to your home
network.
5You have 2 minutes to initiate the connection
process on the extractor hood. See extractor hood
operating instructions.
Once the process is complete, a message will be
displayed, informing you of the result of the connection
process. If the connection has been successfully
established, the S symbol for ventilation control from
the hob will appear on the main screen.
Note: Connection can only be established when both
appliances are connected to your home network and the
connection process has been initiated for both of them.
If the time allowed for connecting has already expired
for one of the two appliances, initiate the connection
process again.
47
Hood control en
Disconnecting from the network
The connection to the home network can be deleted.
1To open the basic settings, touch the t symbol on
the main screen.
2Scroll left or right with your finger and select the
Hood control setting }.
3Select the Disconnect Hood control option and
then touch the G symbol to confirm your choice.
The connections have now been deleted.
Note: The connection to the home network can be re-
established at any time.
Control the hood via the hob
In the hob's basic settings, you can configure what the
extractor hood should do when the hob or individual
cooking positions are switched on or off.
You can select other settings using the control panel.
Setting the fan
Activation
1Touch the H symbol on the main screen.
2Select the fan setting in the settings area. The
following settings are possible:
The following will also be displayed, depending on
which ventilation control setting is selected:
The selected setting will appear on the main screen next
to the H symbol.
Deactivating
Select fan setting 0.
Setting automatic mode
Activation
1Touch the H symbol on the main screen.
2Select the }Hood control option.
3Select the < Automatic option.
Depending on how the extractor hood sensor is
configured, the fan will start automatically when it
detects smoke. For additional information, see extractor
hood operating instructions.
Deactivating
1Touch the H symbol on the main screen.
2Select a different fan setting.
Setting the hood lighting
The hood light can be switched on and off using the
control panel for the cooktop.
1Touch the H symbol on the main screen.
2Select the ž Brightness option.
3Select the brightness level.
Depending on the basic settings you have selected, the
light is automatically switched on or off when the hob is
switched on or off.
0 Fan off
1, 2, 3 Fan settings.
Intensity: Low, medium, high
.Intensive mode
<Automatic mode
žFan run-on
U Unknown mode
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggenau CX482100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggenau CX482100 in the language / languages: English as an attachment in your email.

The manual is 3,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info