702855
10
Zoom out
Zoom in
Previous page
1/32
Next page
10
en Setting up the appliance
Setting up the appliance
Setting up the appliance
Note: Only use the appliance in frost-free areas. If the
appliance was transported or stored at temperatures
below 0 °C, you must wait for at least 3 hours before
using it.
Before the appliance can be switched on and used, it
must be assembled and connected according to the
enclosed installation instructions.
Initial settings
Notes
The query appears automatically when first
switched on after connection to a power outlet.
You can change the settings at any time. ~
"Basic
settings" on page 20
1 Switch on the appliance at the main switch.
The preset language appears in the display.
2 Turn the rotary selector to select the required
display language.
3 Press to confirm.
The temperature unit appears in the display.
4 Use the rotary selector to select the required
temperature unit.
5 Press to confirm.
The preset capacity unit appears in the display.
6 Use the rotary selector to select the required
capacity unit.
7 Press to confirm.
The preset weight unit appears in the display.
8 Use the rotary selector to select the required
weight unit.
9 Press to confirm.
The display shows "Initial set-up complete".. Confirm
with . The appliance is now ready to use.
Note: If the language is changed, the system restarts.
This takes a few seconds.
Setting the water hardness
It is important to set the water hardness correctly so
that the appliance indicates in good time when the
descaling programme should be run. The preset water
hardness is level 4. If a water softening unit is installed
in the household, select the "Softening device" setting.
You can check the water hardness using the enclosed
test strip or by asking your local water supplier.
1 Briefly immerse the enclosed test strip in fresh tap
water, leave it to drip and read off the result after
one minute.
2 Rotate the function selector to S.
3 Use the rotary selector to select "Basic settings"
and touch the symbol.
4 Use the rotary selector to select "Water hardness".
5 Touch the % symbol.
6 Using the rotary selector, set the measured water
hardness.
7 Press to confirm.
The setting has been saved. Touch ' to exit the basic
settings.
'HXWVFK
6SUDFKH
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggenau CM450101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggenau CM450101 in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info