761567
57
Zoom out
Zoom in
Previous page
1/60
Next page
56
en Trouble shooting
--------
Notes
If appears on the display, press and hold the
button for the relevant cooking zone in order to
read the fault code.
If the fault code is not listed in the table, disconnect
the hob from the mains power supply and wait
30 seconds before reconnecting it. If this code is
displayed again, contact the technical after-sales
service and specify which fault code has appeared.
If a fault occurs, the appliance will not switch to
standby mode.
The indicator on the tem-
perature sensor flashes
twice.
The battery in the temperature sensor has
almost run out. You may be interrupted the
next time you cook by the battery running
out.
Replace the 3 V CR2032 battery. See the section enti-
tled "Changing the battery".
The indicator on the tem-
perature sensor flashes
three times.
The temperature sensor is no longer con-
nected.
Press and hold the symbol on the temperature sensor
for eight seconds and then reconnect the temperature
sensor to the hob.
“Š‹‹‹
“Š‹‚‹
The operating voltage is incorrect and out-
side of the normal operating range.
Contact your electricity supplier.
—…‹‹ The hob is not connected correctly. Disconnect the hob from the mains. Make sure that it has
been connected as shown in the circuit diagram.
š“ Demo mode is activated. Disconnect the hob from the mains. Wait 30 seconds
and then reconnect. Touch any touch control within the
next three minutes. Demo mode is switched off.
Display Possible cause Solution
Do not place hot cookware on the control panel.
57
Customer service en
4
Customer service
Customer service
Our after-sales service is there for you if your appliance
needs to be repaired. We will always find an appropriate
solution, also in order to avoid after-sales personnel
having to make unnecessary visits.
Product number (E no.) and
production number (FD no.)
Always quote the E number (product number) and FD
number (production number) of your appliance when
contacting the after-sales service.
The rating plate bearing these numbers can be found:
On the appliance certificate.
On the underside of the hob.
The product number (E no.) can be found on the glass-
ceramic hob. You can check the after-sales service
index (KI) and production number (FD no.) by going to
the basic settings. Refer to the section entitled
~ "Basic settings" to find out how to do this.
Please note that a visit from an after-sales service
engineer is not free of charge in the event that the
appliance has been misused, even during the warranty
period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
Trust the expertise of the manufacturer, and rest
assured that the repair will be carried out by trained
service technicians using original spare parts for your
domestic appliance.
GB 0344 892 8988
Calls charged at local or mobile rate.
IE 01450 2655
0.03 € per minute at peak.
Off peak 0.0088 € per minute.
AU 1300 368 339
NZ 09 477 0492
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggenau CI292112 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggenau CI292112 in the language / languages: English as an attachment in your email.

The manual is 3,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gaggenau CI292112

Gaggenau CI292112 User Manual - German - 60 pages

Gaggenau CI292112 User Manual - Dutch - 60 pages

Gaggenau CI292112 User Manual - French - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info