703230
48
Zoom out
Zoom in
Previous page
1/60
Next page
48
en Hood connection
Connecting appliances via your home network
If the appliances are connected to each other via your
home network, both the hood controls and Home
Connect can be used to operate the hob.
Notes
Make sure you follow the safety instructions in the
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the
hob.~
"Important safety information" on page 6
If the appliance is being operated by means of the
controls on the extractor hood, this mode of
operation always has priority. It is not possible to
use the hood controls on the hob during this time.
In networked standby mode, your appliance
requires a maximum of 2 W.
Setting up
To set up the connection between the hob and cooker
hood, the hob must be switched on.
Connecting directly
Make sure that the extractor hood is switched off.
For more information, refer to the section entitled
"Connecting to the hob" in the instruction manual for
your extractor hood.
Note: If you connect your hob directly to the extractor
hood, it cannot be connected to your home network as
well and you will not be able to use Home Connect.
1 Open the basic settings.
2 Touch the t symbol repeatedly until the ™“
setting appears.
‹”” will be lit on the hotplate display.
3 Set the value to using the twist knob.
will flash on the hotplate display.
4 You have 2 minutes to initiate the connection
process on the extractor hood.
Once the hob is connected to the extractor hood, the
value ‹¯ appears on the hotplate display. The symbols
for the hood controls on the hob are displayed on the
hob's control panel.
Connecting via your home network
You require a router that has WPS functionality.
You require access to your router.If you do not have this,
follow the steps for "Direct connection".
When you begin, make sure that the extractor hood is on
your home network.
1 Open the basic settings.
2 Touch the t symbol repeatedly until the ™“
setting appears.
‹”” will be lit on the hotplate display.
3 Set the value to using the twist knob.
will flash on the hotplate display.
4 Press the WPS button on the router within the next
2 minutes.
The hob will be connected to your home network
and the value ƒ will appear on the hotplate display.
5 Initiate the process for connecting to the extractor
hood.
Once the hob is connected to the extractor hood, the
value ‹¯ appears on the hotplate display. The symbols
for the hood controls on the hob are displayed on the
hob's control panel.
Note: Connection can only be established when both
appliances are connected to your home network and the
connection process has been initiated for both of them.
If the connection process has already timed out for one
of the two appliances, try to connect again (basic
settings, ™“ setting).
Resetting connection
You can reset the connections you have saved for your
home network and extractor hood at any time.
1 Open the basic settings.
2 Touch the t symbol repeatedly until the ™“
setting appears.
3 Set the value to ‹”” using the twist knob.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggenau CI272 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggenau CI272 in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gaggenau CI272

Gaggenau CI272 User Manual - German - 60 pages

Gaggenau CI272 User Manual - Dutch - 60 pages

Gaggenau CI272 User Manual - French - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info