761558
19
Zoom out
Zoom in
Previous page
1/60
Next page
18
en Flex function
Disconnecting the two cooking zones
1Select one of the two cooking zones assigned to
the FlexZone.
2Touch the ª symbol.
3The « symbol appears in the cooking zone display.
The Flex function has been deactivated. The two
cooking zones now operate independently of one
another.
Note: If the hob is switched off, and then switched back
on again later, the flexible cooking zone is reset to
function as two independent hotplates.
FlexPlus cooking zone
The hob has a FlexPlus cooking zone which is located
between the two flexible cooking zones and which
switches on in conjunction with the right- or left-hand
flexible cooking zone. This means that larger cooking
vessels can be used and better cooking results can be
achieved.
The FlexPlus cooking zone always switches on in
conjunction with one of the two flexible cooking zones.
It is not possible to activate these cooking zones
independently.
Notes regarding cookware
The cookware should be positioned centrally for good
thermal detection and distribution.
The cookware should cover the side hotplate and the
FlexPlus cooking zone.
Depending on the size of the cookware, the flexible
cooking zone can be activated as two independent
hotplates or as one hotplate:
Set down the cookware
Oblong cookware
Activate the flexible cooking zone
as two independent hotplates or
as one hotplate.
Large round cookware
Activate the flexible cooking zone
as a single hotplate.
The vessel must not cover the
two side cooking zones and the
FlexPlus cooking zone at the
same time.
19
Transfer function en
Activation
1Set down the cookware on the hotplate and make
sure that it also covers the FlexPlus cooking zone.
2Select the hotplate and the required heat setting.
The hotplate and FlexPlus cooking zone indicators
light up.
The flexible cooking zone is activated.
Note: If the two cooking zones next to the FlexPlus
cooking zone are covered by cookware, the FlexPlus
cooking zone indicator may flash.
To link the FlexPlus cooking zone to the corresponding
cooking zone, lift the cookware and set it back down on
the cooking zone before selecting a heat setting.
Deactivating
Remove the cookware from the hotplate. The displays
go out.
This deactivates the FlexPlus cooking zone.
u
Transfer function
Transfer function
You can use this function to transfer the power level, set
cooking time and selected cooking sensor function from
one cooking zone to another.
To transfer the settings, move the cookware from the
cooking zone that is switched on to another cooking
zone.
This function can also be used on the flexible cooking
zones.
Note: You can find additional information on the correct
positioning of the cookware in the section on ~ "Flex
function"
1Remove any cookware from the hob.
The hotplate indicator will start flashing. The
hotplate will not heat up.
2Set down the cookware on a flexible hotplate within
the next 90 seconds. The new hotplate is detected
and the ˆ symbol lights up. The heat setting that
has been applied will flash in the hotplate display.
3Select the new hotplate within 90 seconds using
the twist knob. The settings have been transferred.
 
Â
[|
\|
X|
Y|
X|
Y| [|
\|
X|
Y| [|
\|
Å
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggenau CI262115 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggenau CI262115 in the language / languages: English as an attachment in your email.

The manual is 3,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gaggenau CI262115

Gaggenau CI262115 User Manual - German - 60 pages

Gaggenau CI262115 User Manual - Dutch - 60 pages

Gaggenau CI262115 User Manual - French - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info