761916
23
Zoom out
Zoom in
Previous page
1/88
Next page
23
Installation en
Wall-mounting the appliance and
levelling it
1First remove the protective film from the back of the
appliance and, following installation, remove the
rest of the film.
2When mounting the appliance, ensure that it
engages properly with the mounting supports.
3If required, the appliance can be moved to the right
or to the left.
4Firmly tighten the screws for the mounting
supports. Hold the bracket firmly when doing so. ¨
5If no duct is to be fitted, screw in the two locking
screws without the bracket. ©
Connecting the pipes
If the extractor hood is to be operated in air extraction
mode, the pipes must be connected. If the extractor
hood is to be operated in air recirculation mode, the
activated charcoal filters provided must be fitted.
Note: If an aluminium pipe is being used, smooth the
connection area beforehand.
Exhaust air pipe, dia. 150 mm (recommended size)
Fit the exhaust air pipe directly to the air-pipe connector
and seal the joint.
Exhaust air pipe, dia. 120 mm
1Fit the reducing connector directly to the air-pipe
connector.
2
Attach the exhaust air pipe to the reducing connector.
3Use suitable means to seal both joints.
Attaching the flue duct
If the extractor hood is to be operated in exhaust-air
mode, a flue duct must be fitted.
The flue duct does not need to be fitted for air-
recirculation mode.
mWarning – Risk of injury!
From sharp edges during installation. Always wear
protective gloves while installing the appliance.
mWarning – Risk of electric shock!
Components inside the appliance may have sharp
edges. These may damage the connecting cable. Do not
kink or pinch the connecting cable during installation.
1Separate the flue duct sections by removing the
adhesive tape.
2Remove the pieces of protective film from both flue
duct sections.
3Push one flue duct section into the other.
Notes
To prevent scratches, lay paper over the edges
of the outer flue duct section to protect the
surface.
The slots of the inner flue duct section point
downwards.
4Place flue ducts sections on the appliance.
5Slide the inner flue duct section upwards, attach it
to the left and right sides of the retaining bracket,
and then slide it down to engage it. ¨
6Screw the flue duct section to the sides of the
retaining bracket using two screws. ©
7Clip the lower flue duct section in at the retaining
bracket. The connection cable must not be
damaged. ª
Note: If an air-recirculation optional accessory has been
fitted and the extractor hood is to be operated without a
flue duct, the cable must be wound onto the connector.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggenau AW250192 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggenau AW250192 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 4,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gaggenau AW250192

Gaggenau AW250192 User Manual - German, Dutch, French, Italian - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info