520093

Futaba T14-MZ Manual

42
Zoom out
Zoom in
Previous page
1/127
Next page
42
<Model Basic Setting Procedure>
4. Fuselage linkage
Connect the throttle rudder, ailerons, elevators,
pitch, and other rudder linkages in accordance with
the kit instruction manual. For a description of
the connection method, see "Receiver and Servos
Connection".
*The channel assignment of the T14MZ is different from
that of our existing systems. (The channel assigned to
each function can be checked at the Function menu of the
Linkage Menu.)
● When the direction of operation of the
linkage is reverse, use the Reverse function
of the Linkage Menu. Also use the swash AFR
function in other than the H-1 mode.
● Adjust the direction of operation of the gyro.
● Adjust the direction of operation of the gyro.
(Gyro side function)
●
Connect the throttle linkage so that the
carburetor becomes full open at trim full
open and throttle cut is possible.
●
Basically, adjust the neutral position and
rudder angle at the linkage side and fine
tune with the Sub-Trim function and End
Point function (rudder angle adjustment). To
protect the linkage, a limit position can also
be set with the End Point function.
● Swash plate correction (Except H-1 mode)
Operation of the swash plate near the hovering
point can be corrected by swash AFR function
correction mixing. Use this when pitch, aileron,
and elevator operation causes the swash plate to
deviate from the normal direction.
(Call the Swash setup→Swash details screen.)
(Call the Swash setup→Swash details screen.)
Pitch slow side and high side linkage correction is
also possible. Adjust so that pitch operation causes
the swash plate to move up and down in the
horizontal state.
5. Throttle cut and pitch curve setting
Call the Throttle Cut or Pitch Curve function
from the Model Menu and set the curve of each
condition.
(17 points curve)
Curve setting up to 17 points is possible, but
in the case of the example below, adjustment by
reducing the set point by using [Linear] or [Curve]
curve type is also possible. This can be used when
there is a specification at the fuselage side and
when setting a simple curve.
*The initial value at curve selection is 9 points setting.
Note: At initial setting, the setting mode is the group
mode. In this mode, the same contents are set at all
the added conditions. When you want to set only
the selected condition, switch to the single mode.
<Setting example>
Call the throttle curve of each condition with the
condition select switch.
A
throttle setting example is shown below.
A
throttle setting example is shown below.
A
●Throttle curve (Normal)
Adjust at each point while watching the response
and speed with hovering (stick 50% position) as the
standard. Since it is connected with pitch, consider
them together.
●Throttle curve (Idle up 1)
This setting maintains the rotation even when the
throttle stick is set to the slow side.
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T14-MZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T14-MZ in the language / languages: English as an attachment in your email.

The manual is 13,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba T14-MZ

Futaba T14-MZ Quick start guide - German - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info