Manual Futaba T14-MZ (page 39 of 127) (English)

520093

Zoom out

Zoom in

1/127

MODEL BASIC SETTING PROCEDURE

1. Model addition and call

Initial setting assigns 1 model to the T14MZ

transmitter. The Model Select function of the

Linkage Menu is used to add models and to call

models which are already set.

This is convenient when calling a model after its

name has been registered. (The data of up to 30 models

can be saved to the transmitter. Data can also be saved

to the accessory Data-Pack.)

The currently called model name is displayed at the

top of the screen. Before flying and before changing

any settings, always conﬁrm the model name.

When a new model was added, the Model type

select screen and Frequency/Modulation mode/

Receiver ID setup screen automatically appear. After

changing or confirming the model, turn the power

off and on in accordance with the instructions on

the screen. And, please be fully aware that the

transmitter will stop transmitting radio wave when

you change the model.

2. Model type selection

Select the model type matched to the fuselage with

the Model Type select function of the Linkage Menu.

For an airplane, select the model type from among the

3 types: airplane, glider, and motor glider. When the

Wing type select screen is displayed and the wing type

is selected when selecting the model type, the Tail type

select screen is displayed. Select the tail type matched

to the fuselage.

There are 13 wing types and 3 tail types for airplane,

glider, and motor glider.

Airplane/glider basic setting procedure

3. Fuselage linkage

Link the ailerons, elevators, throttle, rudder, etc.

in accordance with the model's instruction manual.

For a description of the connection method, see the

Receiver and Servos Connection.

Note: The channel assignment of the T14MZ is

different from that of our existing systems. Note

that even for the same "airplane model", when the

wing type and tail type are different, the channel

ssignment may be different. (The channel assigned

to each function can be checked at the Function

menu of the Linkage Menu.)

● When the direction of operation of the linkage is

reversed, adjust the direction with the Reverse

function of the Linkage Menu.

● Connect the throttle linkage so that the

carburetor becomes full open at trim full open

and the throttle can be cut.

● Basically, adjust the neutral position and rudder

angle with the linkage, and ﬁne tune them with

the Sub Trim and End Point functions (rudder

angle adjustment). To protect the linkage, a

limit position can also be set with the End Point

function. The End Point function can adjust the

amount of up/down and left/right movement,

limit, and servo speed of each channel.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T14-MZ in the language / languages: English as an attachment in your email.

The manual is 13,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba T14-MZ

Futaba T14-MZ Quick start guide - German - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba T14-MZ Manual

Product: