747981
31
Zoom out
Zoom in
Previous page
1/61
Next page
60
61
powered by
Bedienungsanleitung Futaba T4PV www.ripmax.de
(HOME-Bildschirm)
(MENU 2 )
(MENU 3 )
(D/R ATL Ansicht)
(MENU 1 )
Drücke
n
Drücke
n
Drücke
n
Wenn die T4PV mit der Futaba Fail Safe Unit (FSU) betrieben wird, darf der
High Speed Mode
NICHT
aktiviert sein!
Bei am Gas-Kanal angeschlossener FSU und aktivierter ABS-Funktion, blinkt die LED
der FSU bei jeder Servo-Bewegung. Dies bedeutet nicht, dass die Fail Safe Funktion
anspricht!
GRUNDEINSTELLUNG
AB.P: ca. 30% (Bei zu hohen Werten verlängert sich der Bremsweg)
CYCL: 5 ~ 7
DUTY: (Wenig Griff: LOW | Viel Griff: HIGH)
DELY: 10 ~ 15%
TG.P: ca. 70%
FAHRZEUG BRICHT AUS (RÄDER BLOCKIEREN)
AB.P: Wert erhöhen ab 30%
DUTY: Wert "LOW" wählen
DELY: Wert reduzieren
FAHRZEUG BREMST SCHLECHT, BREMSWEG ZU LANG
AB.P: Wert verringern ab 30%
DUTY: Wert "HIGH" wählen
DELY: Wert erhöhen
Einstell-Beispiel (Gas-/Bremsservo S9352HV)
1/5 RC-CARS & MODELLE MIT SEPARATEM BREMSSERVO
Die ABS-Funktion kann auch genutzt werden, wenn mehr als 1 Bremsservo im Modell
verbaut ist und über CH3/CH4 angesteuert wird. Die Programmierung erfolgt über die
Funktion
[
BRK MIX
] .
DUAL RATE (LENKUNG)
Mit dieser Funktion wird der Lenkausschlag für beide Seiten gleichmäßig verändert. Diese Einstellung kann auch über
den Taster DT5 verändert werden. Wenn DT5 eine andere Funktion zugewiesen bekommen hat, kann die Dual Rate
Einstellung in diesem Menüpunkt vorgenommen werden.
ATL (GAS-BREMSE)
Mit dieser Funktion kann während des Fahrens die Bremswirkung erhöht oder verringert werden. Diese Einstellung kann
auch über den Taster DT6 verändert werden. Wenn DT6 eine andere Funktion zugewiesen bekommen hat, kann die ATL
Einstellung in diesem Menüpunkt vorgenommen werden.
DUAL RATE (LENKUNG) / ATL (GAS-BREMSE) "D/R ATL"
AUFRUF DER FUNKTION
[
D/R ATL
]
EINSTELLUNG DUAL RATE (LENKUNG)
1. Wählen Sie mit dem Jog Stick den Punkt *ST-D/R - RATE aus. Anschließend
mit der (+) oder (-) Taste den gewünschten Mode einstellen.
2. Abschließend die END Taste drücken, um die Funktion zu verlassen.
EINSTELLUNG ATL (BREMSE)
1. Wählen Sie mit dem Jog Stick den Punkt *TH-ATL - RATE aus. Anschließend
mit der (+) oder (-) Taste den gewünschten Mode einstellen.
2. Abschließend die END Taste drücken, um die Funktion zu verlassen.
DUAL RATE
0 ~ 100%
Werkseinstellung: 100%
Durch Drücken der (+) oder (-)
Taste wird der Wert verändert.
Durch gleichzeitiges Drücken
von (+) und (-) springt der Wert
auf die Werkseinstellung zurück.
DUAL RATE
0 ~ 100%
Werkseinstellung: 100%
Durch Drücken der (+) oder (-)
Taste wird der Wert verändert.
Durch gleichzeitiges Drücken
von (+) und (-) springt der Wert
auf die Werkseinstellung zurück.
3. FUNKTIONEN
3. FUNKTIONEN
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-4PV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-4PV in the language / languages: German as an attachment in your email.

The manual is 24,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info