747980

Futaba T-32MZ Manual

47
Zoom out
Zoom in
Previous page
1/189
Next page
47
＜
Model Basic Setting Procedure
＞
4. Throttle cut setting
 (
In case of engine
model
)
Throttle cut can be performed with one touch by a switch
without changing the throttle trim position.
Set throttle cut with the Throttle Cut function of the Linkage
Menu. After activating the throttle cut function and selecting
the switch, adjust the throttle position so that the carburetor
becomes full close. For safety, the throttle cut function operates
the throttle stick in the slow position.
5. Idle down setting
 (
In case of engine
model
)
The idling speed can be lowered with one touch by a switch
without changing the throttle trim position. Perform this setting
with the Idle Down function of the Linkage Menu. After
activating the Idle Down function and selecting the switch,
adjust the idle down speed. For safety, the idle down function
acts only when the throttle stick is in the slow position.
*While the Throttle Cut function is in operation, the Idle
Down function does not work.
6. AFR (D/R)
AFR function is used to adjust the throw and operation curve
RIWKHVWLFNOHYHUDQGVZLWFKIXQFWLRQVIRUHDFKÀLJKWFRQGLWLRQ
This is normally used after End Point (ATV) has defined
the maximum throw directions (End Point acts on all flight
condition settings). When mixing is applied from one channel to
another channel, both channels can be adjusted at the same time
by adjusting the operation rate through the AFR function.
7. Airbrake
This function is used when an air brake is necessary when
taking off or diving, etc.
7KHSUHVHWHOHYDWRUVDQGÀDSVFDPEHUÀDSEUDNHÀDSRIIVHW
amount can be activated by a switch.
7KHRIIVHWDPRXQWRIWKHDLOHURQHOHYDWRUDQGÀDSVHUYRVFDQ
be adjusted as needed. Also the speed of the aileron, elevator,
and flap servos can be adjusted. (IN side/OUT side) A delay
can be set for each condition, and a cut switch which will turn
2))WKHGHOD\FDQEHFKRVHQ7ULPDPRXQWVFDQEH¿QHWXQHG
by setting a VR. You can also set the auto mode, which will link
Airbrake to a stick, switch, or dial. A separate stick switch or
dial can also be set as the ON/OFF switch.
$GGLWLRQRIÀLJKWFRQGLWLRQV
7KHWUDQVPLWWHUFDQLQVWDOOXSWRHLJKWÀLJKWFRQGLWLRQVSHU
model. You can assign all switches including sticks, switches,
WULPOHYHUVDQGWULPVZLWFKHVDVIOLJKWFRQGLWLRQVHOHFWLRQ
switches. You can also add delayed mixing to these functions
in order to avoid sudden changes. Moreover, you can set
SULRULW\RUGHUIRUÀLJKWFRQGLWLRQVZKHQ\RXVHWPRUHWKDQRQH
condition. In addition, you can copy conditions and/or change
QDPHVRIFRQGLWLRQV7KLVFRPPDQGPD\DOVREHXVHGWRGH¿QH
what switches and/or controls are used to activate each flight
condition.
The Condition Select function automatically allocates the
condition 1 for each model type. Condition 1 is the default
condition, also referred to as normal, and is the only one active
ZKHQDQHZPRGHOW\SHLVGH¿QHG7KLVFRQGLWLRQLVDOZD\V21
and remains ON until other conditions are activated by switches.
The Condition Delay can be programmed for each channel.
The Condition Delay is used to change the servo throw smoothly
when switching conditions.
*When a new condition is added, "Condition1" data is
automatically copied.
*Select the condition switch and set the new condition data
with the switch in the ON position. However, if the group
mode (Gr.) was selected in advance, the same data will be
input to all new conditions. Select the single mode (Sngl)
and adjust the condition you want to change.
$,53/$1(*/,'(5
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-32MZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-32MZ in the language / languages: English as an attachment in your email.

The manual is 8,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Futaba T-32MZ

Futaba T-32MZ User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info