747919

Futaba T-18MZ-WC Manual

44
Zoom out
Zoom in
Previous page
1/178
Next page
44
＜
Model Basic Setting Procedure
＞
&RQÀUPWKDWWKHUDWHRIWKHVORZHVWSRVLWLRQRI
WKHVWLFNLVLQLWLDOVHWWLQJ
%HVXUHWKDWZKHQVHWWRKLJKVLGHWKHFXUYHRI
DQ\FRQGLWLRQGRHVQRWH[FHHG
Example of pitch curve setting:
1. Call the pitch curve of each condition with
the condition select switch.
*Pitch curve graph display can be switched to pitch angle direct
reading display.
$3LWFKFXUYH1RUPDO
Make the pitch at hovering approximately +5
º
~6
º
.
Set the pitch at hovering with the stick position at
WKHSRLQWDVWKHVWDQGDUG
*Stability at hovering may be connected to the throttle curve.
Adjustment is easy by using the hovering throttle function and
hovering pitch function together.
%3LWFKFXUYH,GOHXS
The idle up 1 pitch curve function creates a curve
PDWFKHGWRDLUERUQHÁLJKW
Set to -7
º
a
º
as standard.
&3LWFKFXUYH,GOHXS
The high side pitch setting is less than idle up 1.
The standard is +8
º
.
D. Pitch curve (Hold)
$WDXWRURWDWLRQXVHWKHPD[LPXPSLWFKDWERWK
the high and low sides.
[Pitch angle setting example]
7KURWWOHKROG
º
a
º
6. Throttle hold setting
Call the Throttle Hold function from the Model
Menu and switch to the throttle hold condition with
the condition select switch.
Note: $WLQLWLDOVHWWLQJWKHVHWWLQJPRGHLVWKH
group mode. Since this function is not used at other
conditions, switch to the single mode before setting.
ŏ6HWWLQJWRWKHVWDWHZKLFKDFWLYDWHVWKHIXQFWLRQ
The throttle hold function allows setting for throttle cut
DQGVZLWFKLQJRIWKHIXQFWLRQÀ[HGDWWKHLGOHSRVLWLRQ
by switch for training. Either one or both functions
can be performed.
ŏ+ROGSRVLWLRQVHWWLQJ
This function sets the servo operation position at
throttle hold. (Throttle cut and idle positions)
ŏ2WKHUVHWWLQJV
When you want to link operation with stick
PDQLSXODWLRQWKH$XWRPRGHFDQEHVHW
When you want to adjust the servo speed, adjust
[Speed].
3LWFKWR58'PL[LQJVHWWLQJ
Use this function when you want to suppress
the torque generated by the changes in the pitch
and speed of the main rotor during pitch operation.
Adjust it so that the nose does not swing in the
rudder direction. However, when using a heading
hold gyro like those shown below, do not use Pitch
to RUD mixing.
Note:KHQXVLQJD)XWDED*<VHULHVJ\URRURWKHU
KHDGLQJKROGJ\URWKLV3LWFKWR58'PL[LQJVKRXOG
not be used. The reaction torque is corrected at
WKHJ\URVLGH:KHQRSHUDWLQJWKHJ\URLQWKH$9&6
mode, the mixed signal will cause neutral deviation
symptoms and the gyro will not operate normally.
Call the Pitch to RUD mixing function from the
Model Menu, and set the curve for each condition.
(At initial setting, this function is in the "INH" state.
To use it, set it to the "ON" state.)
(17 points curve)
Curve setting of up to 17 points is possible.
However, in the following setting example, a simple
curve can be adjusted by using the [Linear] curve
type.
Note:$WLQLWLDOVHWWLQJWKHVHWWLQJPRGHLVWKHJURXS
PRGH,QWKLVPRGHWKHVDPHFRQWHQWVDUHVHWDWLQ
all conditions. When you want to set the selected
condition only, switch to the single mode.
6HWWLQJH[DPSOH!
Call the mixing curve of each condition with the
condition select switch.
The throttle hold curve is used when performing auto
rotation dives.
… 44 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-18MZ-WC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-18MZ-WC in the language / languages: English as an attachment in your email.

The manual is 8,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info