Manual Futaba T-18MZ-WC (page 41 of 178) (English)

747919

Zoom out

Zoom in

1/178

＜

Model Basic Setting Procedure

＞

4. Throttle cut setting

(

In case of engine

model

)

Throttle cut can be performed with one touch by a

switch without changing the throttle trim position.

Set throttle cut with the Throttle Cut function of

the Linkage Menu. After activating the throttle cut

function and selecting the switch, adjust the throttle

position so that the carburetor becomes full close.

For safety, the throttle cut function operates the

throttle stick in the slow position.

5. Idle down setting

(

In case of engine

model

)

The idling speed can be lowered with one touch by

a switch without changing the throttle trim position.

Perform this setting with the Idle Down function of

the Linkage Menu. After activating the Idle Down

function and selecting the switch, adjust the idle

down speed. For safety, the idle down function acts

only when the throttle stick is in the slow position.

*While the Throttle Cut function is in operation, the Idle Down

function does not work.

6. AFR (D/R)

AFR function is used to adjust the throw and

operation curve of the stick, lever, and switch

IXQFWLRQVIRUHDFKÀLJKWFRQGLWLRQ7KLVLVQRUPDOO\

used after End Point (ATV) has defined the

maximum throw directions (End Point acts on ALL

flight condition settings). When mixing is applied

from one channel to another channel, both channels

can be adjusted at the same time by adjusting the

operation rate through the AFR function.

7. Airbrake

This function is used when an air brake is

necessary when taking off or diving, etc.

7KHSUHVHWHOHYDWRUVDQGÀDSVFDPEHUÀDSEUDNH

ÀDSRIIVHWDPRXQWFDQEHDFWLYDWHGE\DVZLWFK

7KHRIIVHWDPRXQWRIWKHDLOHURQHOHYDWRUDQGÀDS

servos can be adjusted as needed. Also the speed of

WKHDLOHURQHOHYDWRUDQGÀDSVHUYRVFDQEHDGMXVWHG

(IN side/OUT side) A delay can be set for each

condition, and a cut switch which will turn OFF the

GHOD\FDQEHFKRVHQ7ULPDPRXQWVFDQEH¿QHWXQHG

by setting a VR. You can also set the auto mode,

which will link Airbrake to a stick, switch, or dial.

A separate stick switch or dial can also be set as the

ON/OFF switch.

$GGLWLRQRIÀLJKWFRQGLWLRQV

The transmitter can install up to eight flight

conditions per model. You can assign all switches

including sticks, switches, trim levers and trim

VZLWFKHVDVÀLJKWFRQGLWLRQVHOHFWLRQVZLWFKHV<RX

can also add delayed mixing to these functions in

order to avoid sudden changes. Moreover, you can

VHWSULRULW\RUGHUIRUÀLJKWFRQGLWLRQVZKHQ\RXVHW

more than one condition. In addition, you can copy

conditions and/or change names of conditions. This

FRPPDQGPD\DOVREHXVHGWRGH¿QHZKDWVZLWFKHV

and/or controls are used to activate each flight

condition.

The Condition Select function automatically

allocates the condition 1 for each model type.

Condition 1 is the default condition, also referred

to as normal, and is the only one active when a new

PRGHOW\SHLVGH¿QHG7KLVFRQGLWLRQLVDOZD\V21

and remains ON until other conditions are activated

by switches.

The Condition Delay can be programmed for each

channel. The Condition Delay is used to change the

servo throw smoothly when switching conditions.

*When a new condition is added, "Condition1" data is

automatically copied.

*Select the condition switch and set the new condition data

with the switch in the ON position. However, if the group

mode (Gr.) was selected in advance, the same data will be

input to all new conditions. Select the single mode (Sngl) and

adjust the condition you want to change.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-18MZ-WC in the language / languages: English as an attachment in your email.

The manual is 8,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Futaba T-18MZ-WC Manual

Product: