747919
23
Zoom out
Zoom in
Previous page
1/178
Next page
23
Before Use
SD Card (sold separately)
7KH6'FDUGFDQVWRUHYDULRXV¿OHVVXFKDVPRGHO
GDWDPXVLFVRXQG¿OHVDQGSLFWXUHV$Q\6'FDUG
on the market can be used with the T18MZ-WC.
The card is locked when it is pushed in all the way
in. To remove the card, push in on the card again, it
will pop up allowing you to remove it.
*Write protection of SD card is turned OFF. In the state of
protection, model data cannot be saved on SD card.
WARNING
Be sure to turn off the power to the transmitter
before inserting or removing the SD card.
As the SD card is a precision device, do not use
excessive force when inserting.
If model data generated by a new software
version transmitter is copied to an old software
version transmitter, the transmitter may operate
erroneously. Copy the model data after updating
the copy destination transmitter to the new
software version.
Read data from a PC
6DYLQJPXVLFDQGLPDJH¿OHVHGLWHGE\D3&LQWRWKH
SD card, you can use those files on your T18MZ-
WC transmitter. Equipment for reading and writing
SD cards are available at most electronics stores.
Stored data
The life of the SD card is limited due to the use
of flash memory. If you have a problem saving or
reading data such as picture data after a long period
of use you may need to purchase a new SD card.
*We are not responsible for, and cannot compensate for any
failure to the data stored in the memory card for any reason.
Be sure to keep a backup of your models and data in your SD
card.
*No need for backup
battery; T18MZ-WC transmitters and
SD cards are using nonvolatile memory devices so that the
data stored in those will not be destroyed even without a
backup battery. The clock for the transmitter depends on the
Lithium battery.
Update Switch
When using an SD card to update the T18MZ-WC
software, set this switch to the up position. Then
input the software to be updated to the SD card
from the Futaba importers homepage and update the
software in accordance with the updating procedure.
USB port
The following functions can be used with USB
connector.
• USB Mouse
When a mouse is connected, a cursor will
appear on the screen and the mouse can be
used instead of the touch panel.
• USB Keybord
When a keyboard is connected, the model
name and other data can be input by
keyboard.
• USB Memory
All model data, etc. can be saved to an
optional USB Memory stick.
Connector for trainer function (TRAINER)
When you use trainer function, connect the optional
trainer cable between the transmitters for teacher and
student.
*You can set the trainer function on the Trainer Function screen
in the system menu
Connector for DSC function (DSC)
You can operate the transmitter without transmitting
radio waves by connecting the transmitter and the
receiver to the DSC cable.
*Please refer to the section "Connection between Receiver/
Servo"
S.BUS connector (S.I/F)
When setting an S.BUS servo and telemetry sensor,
connect them both here.
(Supply power by 3-way hub or 2-way cord.)
Audio plug (PHONE)
Connecting a stereo headphone to this plug, you can
HQMR\PXVLF¿OHVVWRUHGLQWKH6'FDUG
Connector for battery charger (CHG)
You cannot use the charger that was included with
the transmitter, without using the AC adapter that
comes with this.
DANGER
Do not connect any other chargers. The charger
for the receiver battery cannot be used for the
transmitter.
USB port (mini-B)
*This is for factory use only.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-18MZ-WC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-18MZ-WC in the language / languages: English as an attachment in your email.

The manual is 8,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info