747917

Futaba T-16IZ Manual

140
Zoom out
Zoom in
Previous page
1/228
Next page
140
→ GO to TABLE OF CONTENTS
Buttery
[Corresponding model type]: Glider, 2 ailerons or more
This function allows powerful brake operation
by simultaneously raising the left and right
ailerons and lowering the flaps (camber flap,
brake ap).
This setting will allow the ailerons to be raised
while the flaps are simultaneously lowered.
Butterfly (crow) produces an extremely efficient
landing configuration by accomplishing the
following:
1. Slow the aircraft’s velocity.
2. Provide washout at the wing tips to reduce
the tendency to tip stall.
3. Create more lift toward the center of the
wing allowing it to y at a slower speed.
● Mixing during ight can be turned ON/OFF by
setting a switch. (Always ON at [--] setting)
● The buttery operation reference point can be
offset. When the screen is tapped with the offset
item selected when operated to the position to
be changed, the reference point is offset. If the
reference point is offset too much, unexpected
operation may be performed.
● The ailerons and aps operation speed can be
adjusted. (In side/Out side)
● A delay can be set for each condition. A cut
switch which can turn OFF the delay function can
also be set.
● The differential rate can be adjusted.
*When servo binding occurs when setting the ailerons and
aps in buttery mixing, use the AFR function to adjust the
rate.
● Select [Butterfly] at the model
menu and call the setup screen
shown below.
*The display screen is an example. The actual
screen depends on the model type.
When using this
function, Tap [INH].
(ON is displayed.)
Condition group/single
mode selection (Gr. /
Sngl)
The ON/OFF switch of
mixing is chosen.
Condition delay setting
Condition delay cut
switch
To next page
The di󰮏erential rate
can be adjusted.
In speed
Out speed
（First）0 ～ 27（Slowly）（First）0 ～ 27（Slowly）
*The display screen is an example. The actual
screen depends on the Model Type.
When offsetting the butterfly operation
reference point, operate to the throttle
stick point you want to change and then
touch the Offset button. The reference
point displays 0%. When [Yes] is touched,
the reference point is changed. Then,
"Initialize elevator curve?" appears,
allowing you to conrm your setting.
*When dierential rate is "-", the calculation method of UP/
DOWN and a direction become reverse.
*When dierential rate is "+", Up rate is decrease and DOWN
rate is increase.
… 140 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info