747917
103
Zoom out
Zoom in
Previous page
1/228
Next page
103
GO to TABLE OF CONTENTS
*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in
FASSTest12CH mode.
*The FASSTest18CH /T-FHSS mode can use all the telemetry
functions.
Telemetry: Voltage [Battery]
Displaying data from the receiver battery voltage
In this screen, the battery voltage of a receiver is
displayed.
If it becomes higher or lower than the settin, an
alarm and/or vibration will alert you.
Battery voltage
Sets the voltage on
which the alarm
operates.
The "down" arrow
will indicate that an
alarm will sound when
the voltage drops to
below the setting.
Alarm is chosen from
Buzzer, Voice, and
Inhibit.
Allows Speech to be
turned ON or OFF.
● Tap the [Voltage] button in the Telemetry screen
to call the setup screen shown below.
Max. and min. values
since the power
was turned ON will
display.
In this screen, the battery voltage is displayed. In
order to use this function, it is necessary to connect
External voltage connector of R7108SB
SBS-
01V
Battery
SBS-01V measures two batteries. The power
battery connected to two lines is displayed on EXT-
VOLT. The battery for receivers connected to 3P
lines is displayed here.
*SBS-01V must be installed in the aircraft.
Two examples of wiring are shown
*Refer to the manual of SBS-01V for the details of
wiring.
to S.BUS2
port
to S.BUS2
port
R7108SB
R7108SB
Drive battery 1
(EXT Battery)
Receiver battery
Receiver battery
Drive battery 2
(EXT Battery)
Drive battery 1
(EXT Battery)
Drive battery 2
(EXT Battery)
Switch
Power supplies
for servos
Another power
supply Hub
S.BUS2
servos
Two drive batteries are measured (R7108SB use)
Two drive batteries and power supplies for servos are measured (R7108SB use)
●Battery voltage measurement for receivers [R7108SB use]
●The drive battery 1 is measured in an EXT port [R7108SB use]
●The drive battery 2 is measured in an EXT line [SBS-01V use]
●Battery voltage measurement for receivers [R7108SB use]
●The drive battery 1 is measured in an EXT port [R7108SB use]
●The drive battery 2 is measured in an EXT line [SBS-01V use]
●The voltage for servos is measured in a power supply line [SBS-01V use]
Normal Line
Normal Line
EXT Line
EXT Line
*SBS-01V measures two voltage. One corresponds to high voltages, such as a drive battery,
with an EXT line. Another is a normal line and is measurement of the battery for receivers of a
line connected to 3P connector, or the battery for servos.
Alarm set
1. Tap Alarm and choose from Buzzer,
Voice, and Inhibit.
2. Choose "Inhibit" for Vibrator if not using
the vibrator alarm. If using vibrator,
choose one of the three types.
3. Tap to the Limit [4.0 V] item.
4. Adjust the rate using the "▼▼" "▼" "▲"
"▲▲" buttons.
Initial value: 4.0 V
Adjustment range: 0.0 V~100.0 V
*When the screen is tapped for one second, the rate is
reset to the initial value.
5. To terminate the input and return to
the original state, push the HOME/EXIT
button.
Vibrator choices are
type1-3, and Inhibit.
●Return to
Linkage menu
103


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba T-16IZ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba T-16IZ in the language / languages: English as an attachment in your email.

The manual is 35,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info